Author Topic: clutch mb strength (Read 2544 times)

rene- · « **on:** December 30, 2009, 12:49:38 AM »

i have an undrilled clutch and plan on getting it drilled soon. can someone give me the mb strength or mb rating? could not find any infos.

thanks,

rene
--------------------
www.900global.com
www.amf300.com

icewall · « **Reply #1 on:** December 30, 2009, 08:54:16 AM »

.009

found it on the shelf talker
--------------------
tweener
med revs
med speed
low tilt
low average

surface_solutions · « **Reply #2 on:** January 02, 2010, 05:01:29 PM »

Pretty non existent.

--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

charlest · « **Reply #3 on:** January 02, 2010, 05:25:08 PM »

.009 is not insignificant. In fact, it's just the right side of which must be taken into account for drilling. It will have an effect.

--------------------
"None are so blind as those who will not see."

surface_solutions · « **Reply #4 on:** January 02, 2010, 07:20:15 PM »

From what I understand, most of recreational league bowlers aren't even good enough to take advantage of a mass bias. We just are consistent enough.
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

charlest · « **Reply #5 on:** January 02, 2010, 07:34:14 PM »

quote:
From what I understand, most of recreational league bowlers aren't even good enough to take advantage of a mass bias. We just are consistent enough.
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

That's ... a different matter.
Technically the cutoff point for importance of MB is .008". Anything at or above that should be taken into account when drilling. That's the gospel according to St. Mo. Whatever else your opinion of him might be, you can't argue with him technically.
--------------------
"None are so blind as those who will not see."

surface_solutions · « **Reply #6 on:** January 03, 2010, 08:11:56 AM »

Oh yea, I completey agree and I have no arguement there. I wasn't aware of the exact number, but that it was I had understood for markings also.

*I also see that I fat fingered the last thread,"it should have read that we just are NOT consistent enough"

I will also back the argurement that no matter the skill level of the bowler in question the MB can be used to fine tune a ball for said bowler. That is what all the research that has been done the last decade plus supports, I get it.

But if my ball has been tuned to give me the best look and reaction bouncing off the 10 board but I can't hit it two out of five. What good is it doing me?

--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

charlest · « **Reply #7 on:** January 03, 2010, 12:10:40 PM »

quote:
But if my ball has been tuned to give me the best look and reaction bouncing off the 10 board but I can't hit it two out of five. What good is it doing me?
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

None, that's why we have house balls!

--------------------
"None are so blind as those who will not see."

surface_solutions · « **Reply #8 on:** January 03, 2010, 12:31:07 PM »

Fair enough, but boy have I waisted a lot of money! LOL Atleast my hand doesn't hurt and the end of the night.
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com
{Be sure to inlcude _ if sending e-mails or payment to paypal}

Author Topic: clutch mb strength (Read 2544 times)

rene-

clutch mb strength

icewall

Re: clutch mb strength

surface_solutions

Re: clutch mb strength

charlest

Re: clutch mb strength

surface_solutions

Re: clutch mb strength

charlest

Re: clutch mb strength

surface_solutions

Re: clutch mb strength

charlest

Re: clutch mb strength

surface_solutions

Re: clutch mb strength