Author Topic: dexter replacement heel? (Read 8956 times)

10pin hater · « **on:** October 26, 2009, 12:53:51 PM »

this is probably a stupid ? but im ordering some replacement heels on bowlingball.com and they have two different sizes small and large but it doesn't tell you which ones fit what size shoes can someone please help me so i dont buy the wrong ones thank you

Pat Patterson · « **Reply #1 on:** October 26, 2009, 09:39:52 PM »

Here is the size range for heel replacement from Dexter:

LARGE: Men's 6.5-15 and Women's 8.5-11.

SMALL: Women's 5-11 and Men's 6.5-9.

--------------------
Pat Patterson

10pin hater · « **Reply #2 on:** October 26, 2009, 09:51:40 PM »

thanks a lot pat

slashrr69 · « **Reply #3 on:** October 27, 2009, 02:20:28 AM »

10pin hater

pat not saying you are incorrect, but double check the sizes, I just went through this with trying to find a replacement heel for my dexter sst6 lx(size 11m).. a young lady straight from the dexter customer service line told me for the mens heel "small" is 6-10.5, and "large" 11-15.. the small is actually 1/4" smaller in width and height all the way around the heel.. I ordered 11M and was sent a 10.5(10.5 was stamped on the black velcro side in white ink) and it was too small for my shoe.. had to send it back for a refund, just double check before you order.. slashrr69

Edited on 10/27/2009 2:25 AM

bannachb · « **Reply #4 on:** November 09, 2009, 09:32:52 PM »

I wear size 13 Dexter SST7s. I ordered size large heel and it is WAY too big. I have dealt with heels that are a little bigger before and i just offset them a little bit to the left (I'm right handed) and every thing is fine. But when I offset this new heel it sticks out almost 3/4" out the left side of the shoe. I feel like I am walking around with half a snow shoe on. Has anyone trimmed down one of the heels before? If so what is the recommended way of doing it?

slashrr69 · « **Reply #5 on:** November 09, 2009, 11:33:01 PM »

yes, you are suppose to trim them down.. you take your shoe and place it on the new heel.. trace the shoe heel to the new heel and cut with a pair of tinsnip scissors(must be tinsnips or you will not cut through the material correctly).. when cutting make sure to stay to the outside of the traced line, this will make sure the heel stays wide enough for your shoe.. you can use a soft buffing wheel to smooth out the rougher edges when finished..

surface_solutions · « **Reply #6 on:** November 10, 2009, 01:49:51 AM »

I suppose I am guilty of the same, I had no idea the heels where intended to be trimmed...
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com

bannachb · « **Reply #7 on:** November 10, 2009, 08:45:36 AM »

I know you are SUPPOSED to trim them. I am asking how. The heels that were a little big before were only like 1/8 inch over hang so it was no big deal and it didn't make sense to trim them. Now I have to trim it and I am wondering what the best way to do it is.

bannachb · « **Reply #8 on:** November 10, 2009, 12:06:14 PM »

I now know why SO many people hate this discussion board. If you don't like the question posted PLEASE do not respond to it. Scissors??? Wow that NEVER crossed my mind (sarcasm). I personally think the heel is too thick for scissors. But "obviously" they are the BEST option for cutting the heels so hey, thanks for answer.

eglleftcoast · « **Reply #9 on:** November 10, 2009, 12:07:46 PM »

I've found using a power grinding wheel works the best for me. You still copy one of the original factory heels dimensions to the new heel and then put it to the grinder. The results are much more accurate than using a scissors....

slashrr69 · « **Reply #10 on:** November 10, 2009, 01:40:02 PM »

they recommend using "tinsnips" as I stated up above.. then buff out with a soft buffing wheel to smooth the edges.. as "eleftcoast' suggested using a small grind/cutting wheel might work as well..

SegaMan73 · « **Reply #11 on:** November 10, 2009, 11:43:17 PM »

Hey StormBowler83, are you sure you know that he's talking about trimming a HEEL and not a SOLE because it is obvious to trim a SOLE with scissors but it is NOT obvious to trim a HEEL with scissors. Maybe it's possible you got confused in what he was asking about.

bannachb · « **Reply #12 on:** November 11, 2009, 10:21:45 AM »

Thank you SegaMan... Let's do a little more clearing up just to make sure we are all on the same page. The HEEL is the back part of the shoe, normally made of HARD rubber.

Leftyhi-trak · « **Reply #13 on:** November 11, 2009, 01:08:13 PM »

Cutting wheel, band saw, jig saw, saw-saw, or electric shears work, tried all of above and just smooth out edges. Yes some people use scissors, would recommend the industrial grade (large) as its easier to use.

Author Topic: dexter replacement heel? (Read 8956 times)

10pin hater

dexter replacement heel?

Pat Patterson

Re: dexter replacement heel?

10pin hater

Re: dexter replacement heel?

slashrr69

Re: dexter replacement heel?

bannachb

Re: dexter replacement heel?

slashrr69

Re: dexter replacement heel?

surface_solutions

Re: dexter replacement heel?

bannachb

Re: dexter replacement heel?

bannachb

Re: dexter replacement heel?

eglleftcoast

Re: dexter replacement heel?

slashrr69

Re: dexter replacement heel?

SegaMan73

Re: dexter replacement heel?

bannachb

Re: dexter replacement heel?

Leftyhi-trak

Re: dexter replacement heel?