win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Fuze Igniter/ Raging Red selection question  (Read 2380 times)

Buckwild

  • Hero Member
  • *****
  • Posts: 1038
Fuze Igniter/ Raging Red selection question
« on: June 23, 2003, 08:11:51 AM »
Right now I have a Inferno, stacked leverage, and a Red/Black Monster, pin under ring, cg a little to the right, with a small hole. I've been looking on Ebay, and I see a lot of Raging Red Fuzes, and Fuze Igniters for cheap. Could I use one of those balls, considering what I have already, or the two Fuzes overlap them?
Thanks.

Edited on 6/23/2003 11:17 PM
Logged

 

Bjaardker

  • Hero Member
  • *****
  • Posts: 2387
Re: Fuze Igniter/ Raging Red selection question
« Reply #1 on: June 23, 2003, 11:27:13 PM »
The inferno & Raging Red might cross over a little too much.

However the igniter should go a lot longer than the inferno as long as you dont drill it to turn really early. I find my igniter to be great on screaming back ends or medium length oil. However when the oil gets a little long or there's carrydown to contend with, I simply dont have enough hand to get it to turn the corner. Your experience may be different.
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Fuze Igniter/ Raging Red selection question
« Reply #2 on: June 25, 2003, 11:49:13 PM »
Both are snappier than what you got.  Red earlier than the Igniter.

Me I like the Smash/r but it is not far from your Inferno.

Good luck,

Luckylefty
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

Buckwild

  • Hero Member
  • *****
  • Posts: 1038
Re: Fuze Igniter/ Raging Red selection question
« Reply #3 on: June 26, 2003, 11:40:12 AM »
Thanks for the replies. If you had to choose between the Red and the Iginter, and you already own The Inferno, and The Monster Red/Black, which would you chooes?
Logged

RSalas

  • Hero Member
  • *****
  • Posts: 4058
Re: Fuze Igniter/ Raging Red selection question
« Reply #4 on: June 26, 2003, 11:58:00 AM »
I guess the question that I have is what type of reaction you're looking for.  Are you looking for a specific shot shape that the other two don't give you, or just something that fits between the Inferno and Red/Black?  If it were me, and the latter were true, I'd opt for the Raging Red.  However, if I was looking for something to give me better length and a sharper back end, I'd go for the Igniter.

So was that sufficiently vague for you?  
Logged
#TweetYourScores

Buckwild

  • Hero Member
  • *****
  • Posts: 1038
Re: Fuze Igniter/ Raging Red selection question
« Reply #5 on: June 26, 2003, 01:19:11 PM »
Poöter Boöf,
 You got me with the vague comment. I now understand that there is not much difference between the Raging Red and the Inferno, so if I got one, it would be to have on hand to replace the Inferno. What I didn't get from the replies was how close the Igniter was to the Red/Black. I would do the same if they were that close.
Logged

RSalas

  • Hero Member
  • *****
  • Posts: 4058
Re: Fuze Igniter/ Raging Red selection question
« Reply #6 on: June 26, 2003, 01:44:11 PM »
To me, the Igniter and the Red/Black are very different.  The Red/Black tends to be smoother from front to back;  when I first threw it, the look that I got reminded me of the Sapphire Zone, except cleaner in front.  The Igniter wants to be a lot skiddier in front and snappier off of the dry boards, almost like a highly polished V2 Pearl, but with more lope.  Again, these are my observations;  your mileage may vary.

If you wanted to duplicate the reaction of the Red/Black, you could probably experiment with scuffing and re-polishing the Igniter and get it fairly close.  However, you'd be better off just buying another Red/Black;  after all, they're a lot cheaper.

Hope this helps.
Logged
#TweetYourScores
Pages: [1]
« previous next »