win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Ric Hamlin...................................  (Read 2282 times)

Monster Stitch

  • Hero Member
  • *****
  • Posts: 1490
Ric Hamlin...................................
« on: April 05, 2005, 02:00:58 PM »
The drill pattern you said would work on oily lanes
with the Pin in the center of the grip with the CG kicked out
hole 6-3/4 down, would that particular pattern work for a
high track player and rev challenged??
--------------------
"Learn to throw a lot of strikes" - Tony Reyes
Logged

 

laufaye

  • Hero Member
  • *****
  • Posts: 1602
Re: Ric Hamlin...................................
« Reply #1 on: April 05, 2005, 11:04:40 PM »
Ric,

I need a little help on this one too, I found a used Erase-IT PBT on the used ball rack, plugged and drilled up this layout, this ball just goes lonnnng, with a very smoth arc, but I dont see it reading any midlane at all.  I have about 1" flare maybe LOL.

My PAP 5 1/2 over 3/4 up, track about 1" left of finger and thumb.  about 350 rpm, 10* tilt, 30-45* rotation and roughly 16mph.

I know this layout is not really good for me coz I dont have much rev, but I see it wanna try it, test it out.  I think all drillers have the same kind of sickness.LOL
--------------------
Laufaye
Logged

Monster Stitch

  • Hero Member
  • *****
  • Posts: 1490
Re: Ric Hamlin...................................
« Reply #2 on: April 06, 2005, 01:17:09 PM »
Thanks Bear for the Response.

Ric: This is for my dad actually. His Pap is about 5 to 5-1/2.
His track starts out about 2 to 2.5 inches from his fingers and one inch from his thumb. He has a 230 rev rate or a little less, 60 to 90 degree axis tilt (3/4 roller)and throws 13 to 15 mph. His weakness is heavy heads and mids and getitng the ball back at the end when they are tight.

A lot of his equipment is laid out pin under ring with the cg kicked out in the thumb quadrant with a x-hole low. This helps his ball get in a roll early but the ball arcs in the back.

I'm not sure if a label higher pin layout will help him more or maybe an axis lev layout.
--------------------
"Learn to throw a lot of strikes" - Tony Reyes

Edited on 4/6/2005 4:27 PM
Logged

BrunsNick

  • Brunswick Rep
  • Hero Member
  • *
  • Posts: 7306
Re: Ric Hamlin...................................
« Reply #3 on: April 06, 2005, 03:35:26 PM »
It is more so the fingers that will hit with the flare, as far as a "safe" PAP, Ric would know better. If I had to guess anything past 5 1/8th-5 1/4" is cutting it close.

If you're inverted, pretty much forget about it!

--------------------
Nick Smith ... A.K.A. Les Badderâ„¢
Brunswick -=- PBA 03-05
¡Viva la nación de Brunswick!
Logged
Nick Smith
Digital Media Manager - Brunswick Bowling
http://www.brunswickbowling.com
http://www.youtube.com/c/brunsnick

BrunsNick

  • Brunswick Rep
  • Hero Member
  • *
  • Posts: 7306
Re: Ric Hamlin...................................
« Reply #4 on: April 06, 2005, 04:18:15 PM »
Hahah... I didn't say PERVERTED!
--------------------
Nick Smith ... A.K.A. Les Badderâ„¢
Brunswick -=- PBA 03-05
¡Viva la nación de Brunswick!
Logged
Nick Smith
Digital Media Manager - Brunswick Bowling
http://www.brunswickbowling.com
http://www.youtube.com/c/brunsnick

Monster Stitch

  • Hero Member
  • *****
  • Posts: 1490
Re: Ric Hamlin...................................
« Reply #5 on: April 07, 2005, 12:03:52 PM »
Let me know Rick.
--------------------
"Learn to throw a lot of strikes" - Tony Reyes
Logged

Monster Stitch

  • Hero Member
  • *****
  • Posts: 1490
Re: Ric Hamlin...................................
« Reply #6 on: April 07, 2005, 06:02:25 PM »
BrunsRicH: So i should get him a starter to be his Bench mark ball.

What layout would you suggest and what ball from Brunswick?


--------------------
"Learn to throw a lot of strikes" - Tony Reyes
Logged
Pages: [1]
« previous next »