win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Wild Ride drilling  (Read 3629 times)

CharlieBrown

  • Hero Member
  • *****
  • Posts: 1427
Wild Ride drilling
« on: January 17, 2009, 01:46:15 AM »
Haven't picked one up yet.... but..

With the same medium RG Torsion Asymmetric core as the Twisted, would you recommand to drill it 0.5' closer to PAP (i.e slightly stronger than your usual favorite layout), as suggested in the Twisted video?

Thanks.


--------------------
I''m a THS hack and a ball junkie.
Logged
Certified ball collector.

 

  • Guest
Re: Wild Ride drilling
« Reply #1 on: January 17, 2009, 10:26:12 AM »
It wouldn't hurt, but it depends on what you'd like from the ball. The cover on the Wild Ride is a much stronger pearl, so that may influence your decision. If I'm not mistaken, mine have a similar (if not same) layout, but that's just a great one for me personally, so I've drilled several that way.

The other advantage is that it's easier to compare the two balls (Twisted and Wild Ride) if they're drilled similarly. My layout, etc. was posted on a review the other day in case you want to see... Good luck.




--------------------
Lane Carter, Strike Zone Pro Shops - Salt Lake City, Utah
Brunswick Amateur Staff
www.brunswickbowling.com
Logged

J Dubs

  • Full Member
  • ***
  • Posts: 108
Re: Wild Ride drilling
« Reply #2 on: January 17, 2009, 10:26:15 AM »
I would say Yes. The cover is strong but the core is still very mild in its differential. You might want to put the pin higher up than normal as I did and my WILD Ride is a home run.
--------------------
Stay Focused and Make the Shot

Buy your new high end bowling equipment at Jay Marine's Perfect Fit Pro Shop,
2 Locations, Inside PLAINVIEW Lanes 516 470 0039 ... as well as located inside PORT JEFF BOWL! - 631 476-7550!!!  

Both shops operated by PBA Members
Logged

CharlieBrown

  • Hero Member
  • *****
  • Posts: 1427
Re: Wild Ride drilling
« Reply #3 on: January 17, 2009, 11:49:51 AM »
Thanks Lane.

My PAP has changed quite a bit since I drilled my Twisted so the Twisted is now pin-up 5.5' pin to PAP. (it's weak!)

My favorite drilling is pin down 4.5' - 4.75' pin to PAP, pin down. So if I was to get the Wild Ride (very likely but need some cash first ), I'll probably drill it closer to 4.5 pin to PAP.


J Dubs

Pin down usually works better for me (unless it's short pattern), cos my PAP is 4' 3/8 over 1/8 up, so usually I need some help to get the ball into 'roll', esp in heavier condition. Will speak to my driller though (when I got the ball). Thanks!



--------------------
I'm a THS hack and a ball junkie.
Logged
Certified ball collector.

bluerrpilot

  • Hero Member
  • *****
  • Posts: 1235
Re: Wild Ride drilling
« Reply #4 on: January 17, 2009, 10:11:43 PM »
Since the ball isnt a high flaring ball, I would not be afraid of laying it out with the pin in a stronger position that your used to.
--------------------
"USBC is concerned that technology has overtaken player skill in determining success in the sport of bowling"
Logged

RSalas

  • Hero Member
  • *****
  • Posts: 4058
Re: Wild Ride drilling
« Reply #5 on: January 17, 2009, 10:14:11 PM »
Yes, it would be a good idea to go 1/2" closer to the leverage point with the pin-to-PAP distance.
--------------------
Ray Salas
Brunswick Amateur Staff
http://www.brunswickbowling.com
Logged
#TweetYourScores

TWOHAND834

  • Hero Member
  • *****
  • Posts: 4361
Re: Wild Ride drilling
« Reply #6 on: January 18, 2009, 01:23:06 PM »
Charlie,

I would keep it simple.  Since you like the pin down stuff, lay the ball out with the pin right below the bridge (puts pin just under that 4 1/2 number).  Then, as far as how much "roll" you are looking for, is how much is swing out the cg and add a weight hole if needed.
--------------------
Steven Vance
Pro Shop Operator
Striking Results Pro Shop
Red Carpet Lanes
Duluth (NE Atlanta), Georgia

If anyone out there is worried about the scores being too high, try duckpin!!
Logged
Steven Vance
Former Pro Shop Operator
Former Classic Products Assistant Manager

CharlieBrown

  • Hero Member
  • *****
  • Posts: 1427
Re: Wild Ride drilling
« Reply #7 on: January 20, 2009, 02:19:58 AM »
cheers everyone!
--------------------
I'm a THS hack and a ball junkie.
Logged
Certified ball collector.

Corey C

  • Sr. Member
  • ****
  • Posts: 348
Re: Wild Ride drilling
« Reply #8 on: January 20, 2009, 07:50:45 PM »
I layed mine out 4.5" pin to PAP and I normally use a 5" pin to pap. IMO it was a wise decision. It rolls great!
--------------------
Corey Clayton
Brunswick Amateur Staff
Turbo Grips Staff
Team Canada 2007, 2008, & 2009
Logged
Corey Clayton
Brunswick Regional Staff
Turbo Staff

CharlieBrown

  • Hero Member
  • *****
  • Posts: 1427
Re: Wild Ride drilling
« Reply #9 on: January 21, 2009, 10:55:04 AM »
quote:
I layed mine out 4.5" pin to PAP and I normally use a 5" pin to pap. IMO it was a wise decision. It rolls great!


Thnaks Corey!
--------------------
I'm a THS hack and a ball junkie.
Logged
Certified ball collector.
Pages: [1]
« previous next »