win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Adding a Hole to Lower the Track  (Read 1788 times)

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Adding a Hole to Lower the Track
« on: April 13, 2006, 02:28:48 PM »
I picked up a pin in urethane ball recently and I am tracking very close to the holes. I recall Brunswick or someone having a section somewhere about adding a hole in a specific location to move the bowtie and track away from the holes.

I have the article here somewhere but I cannot locate it. Can anyone out there help me out?

Thanks!!!
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Only the FOS has the Power of the Cobalt!
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

 

TheDude

  • Hero Member
  • *****
  • Posts: 3170
Re: Adding a Hole to Lower the Track
« Reply #1 on: April 13, 2006, 11:43:22 PM »
Place the hole about 2 1/2 inches below your PAP. should increase the flare and draw the bowtie away from your fingers or thumb faster.
--------------------
Timothy @Juniors Pro-Shop
Staff Writer 7-10 Split Magazine,EGO Communications
Montreal, Quebec.
Logged
Timothy @Juniors Pro-Shops
LaSalle, Quebec-Located inside Pont Mercier Lanes.
Keep them honest!

Ebay store updated very often: http://stores.ebay.com/gumby3170?refid+store

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Re: Adding a Hole to Lower the Track
« Reply #2 on: April 14, 2006, 11:16:21 PM »
Thanks Tim.......that's similar to what I have been told but I was told to just make sure the hole was below the pin to PAP line.

maybe 2-1/2" below and past the PAP?
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Only the FOS has the Power of the Cobalt!
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

TheDude

  • Hero Member
  • *****
  • Posts: 3170
Re: Adding a Hole to Lower the Track
« Reply #3 on: April 14, 2006, 11:50:35 PM »
Actually yes, that is true because if the hole is too low it could just pull the bowtie lower towards your fingers.

Try 2 1/2 inches it should do something.
--------------------
Timothy @Juniors Pro-Shop
Staff Writer 7-10 Split Magazine,EGO Communications
Montreal, Quebec.
Logged
Timothy @Juniors Pro-Shops
LaSalle, Quebec-Located inside Pont Mercier Lanes.
Keep them honest!

Ebay store updated very often: http://stores.ebay.com/gumby3170?refid+store

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Re: Adding a Hole to Lower the Track
« Reply #4 on: April 18, 2006, 09:15:39 PM »
Just to update....IT WORKED!!!!

Threw the ball 2-3 times to get my PAP for the ball dialed in. Laid out the VAL and dropped a spot 2-1/2" down and then added a 5/8 hole 2-1/2" deep with a 1" right lateral pitch.

This was enough to move the PAP about an inch and force the ball to triple it's flare and keep the roll off the middle and thumbholes.

Thanks again Dude!!!!
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Only the FOS has the Power of the Cobalt!
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

TheDude

  • Hero Member
  • *****
  • Posts: 3170
Re: Adding a Hole to Lower the Track
« Reply #5 on: April 19, 2006, 12:09:48 AM »
Sweet!!!!!!!!! haha TheDude strikes again!
--------------------
Timothy @Juniors Pro-Shop
Staff Writer 7-10 Split Magazine,EGO Communications
Montreal, Quebec.
Logged
Timothy @Juniors Pro-Shops
LaSalle, Quebec-Located inside Pont Mercier Lanes.
Keep them honest!

Ebay store updated very often: http://stores.ebay.com/gumby3170?refid+store
Pages: [1]
« previous next »