win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl  (Read 3568 times)

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« on: October 22, 2007, 01:15:09 AM »
Let me start of by saying even though I have often disagreed with Brunswick theories as to WHY their drillings work....I have often used their drill sheets with success.

I had been looking for go long drillings at a house I bowl at (at least for practice with little push after the arrows(they don't oil there before league putting out ONLY 14 foot head shot right before league...yuch!).

I had tried 4L on an Ebonite Xcel (with CG near grip center say 1/3 ounce sideweight and mass bias touching thumb...we don't want ANY midlane at this house the lane supplies it!).  The ball was frankly just MILD and meek. Pin about 1 1/2 inches ABOVE my ring finger(about 5 3/4 pin to PAP for me)

I had seen this ball look great for a few occassional righties in this house.

So I saw the smarts in the Brunswick drill sheet and noing I wanted push but more backend(usually carrydown and slop in the last 15 feet at this house) I converted the 4L to a 3L.  I only went 1 inch deep with my 31/32 drill bit as to the already low side weight.

Can you say MONSTER.  Though if one has the slightest pull and dont drive the ball hard out wide of 8 at the break point at this house one will cross over.

If one gets into the proper break zone out near 8 balls struggle to carry.
Not this power house.  I had anywhere from 1 to 8 at the break to smash the pocket and most carried from this monster.

This strong unsung ball reacts similar in this house to my much more strongly drilled Sonic Boom in this house (4 X 4 with pin as high as ring for this much higher RG ball).  But there is probably a little more continuation and a few boards more area from the much stronger cored Xcel!

REgards,

Luckylefty
PS I just hope they don't tell me that Brunswick drillings don't work on Ebonite balls!
PPS drill 3L for length and if too weak...add that powering weighthole!  Cool!
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

 

MegaMav

  • Hero Member
  • *****
  • Posts: 3409
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #1 on: October 22, 2007, 10:49:49 AM »
Good job, X-Holes can fine tune a reaction you're looking for.
Where was the X-Hole located according to your PAP?
Methinks past PAP?
Logged

J_Mac

  • Hero Member
  • *****
  • Posts: 6778
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #2 on: October 22, 2007, 07:27:01 PM »
Why are you using symmetric layouts on a asymmetric ball?
--------------------
"A word to the wise ain't necessary -- it's the stupid ones that need the advice."  Bill Cosby
"Never argue with an idiot. They bring you down to their level and beat you with experience."
Logged

J_Mac

  • Hero Member
  • *****
  • Posts: 6778
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #3 on: October 22, 2007, 08:14:36 PM »
quote:
Because he is the village idiot on this website.


I was thinking poster child for adult ADHD...
--------------------
"A word to the wise ain't necessary -- it's the stupid ones that need the advice."  Bill Cosby
"Never argue with an idiot. They bring you down to their level and beat you with experience."
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #4 on: October 23, 2007, 08:53:32 AM »
Ummmm, love some of these guys on this site.

Was well aware of where the mass bias was...and was tweaking the ball for final tuning.

As many know putting mass bias under the thumb(at least per Mo Pinel) takes much of the mass bias effect out.

See SuperSymmetric drilling from Mo Pinel...Brainiacs...

Ball is reacting great...is that not the objective?

REgards,

Luckylefty
PS observers of the new ball reaction loved it also!
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #5 on: October 23, 2007, 05:43:08 PM »
Imagine, being so weak in personality that you have to create IDs to chase after other guys!  SAd.

Look at this guy Mr. CrankMeisters profile...

"Lefty Lucky's polar opposite personality.

Smart, unbiased and rational."

An ID created solely to follow me around the site....How SAD for you.  What a very very small person you are....

Comparing smart great posters like Bob Hanson to this on this site is like comparing mountains to pits.  Or in this case the bottom of a pit!


AND with the complete approval of site management this guys wayward comments as he has been reported many times.

Could he be either a pro bowler, company rep, or a member of one of the affiliated companies of this site is my assumption though I can't prove it.  Operating with complete protection of the site.  All I know is after I reported his comments last time which would have had any of us kicked off this site...this new rule was created..

BallReviews-TECH
 Show Profile  Contact User Add to Address Book  Ignore User     Posted: 8/10/2007 4:00 PM Some people at BallReviews choose to have multiple usernames for whatever reason. Because we see some valid reasons for doing so (e.g. a rep for company x who wants to make posts as personal views not associated with the company he/she works for), we do not prevent you from doing so. Please note that if a username is created to break the rules of the site or to deceive others by making them think you are another user (e.g. signing up under the name M3gaMav so people will think you are MegaMav), we will block all of your usernames from this site.

-BR-Tech

Sweet...if one doesn't have the courage to post under one name.

As to teabagging it must be a Gay term that I am unfamiliar with but he seems to be very familiar with.

Luckylefty
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..

Edited on 10/23/2007 6:12 PM
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

J_Mac

  • Hero Member
  • *****
  • Posts: 6778
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #6 on: October 23, 2007, 06:05:11 PM »
quote:


An ID created solely to follow me around the site....How SAD for you.  What a very very small person you are....


You really think someone has it out for you, don't you?  

I'm quite familiar with the Super Symmetric layouts from Mo, but if I'm supposed to reference them, why are you talking about Brunswick symmetric ball layouts?

Your train of thoughts are so scatter brained someone would have to read 3 of your posts on a topic to actually see the picture you're trying to draw.

Here's a link for you... if you don't like it here, feel free to use it frequently!


--------------------
"A word to the wise ain't necessary -- it's the stupid ones that need the advice."  Bill Cosby
"Never argue with an idiot. They bring you down to their level and beat you with experience."
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #7 on: October 23, 2007, 06:15:07 PM »
You know my id...you hate my posts...don't read them...you'll avoid confusion.

Don't try this drilling, don't try this ball...you'll be better off for it..right?

REgards,

Luckylefty
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

headwest

  • Sr. Member
  • ****
  • Posts: 325
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #8 on: October 23, 2007, 10:27:48 PM »
quote:
You know my id...you hate my posts...don't read them...you'll avoid confusion.

Don't try this drilling, don't try this ball...you'll be better off for it..right?

REgards,

Luckylefty
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
I'm not sure why so many try to prove how smart they are by busting on others,you can post your opinion with out being an Ahole.
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Brunswick Drilling 3L & 4L and Ebonite Xcel Pearl
« Reply #9 on: October 23, 2007, 10:57:12 PM »
YOu have no idea....

But you will

Thank you..

Luckylefty
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana
Pages: [1]
« previous next »