win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: drillers  (Read 4335 times)

xrayjay

  • Hero Member
  • *****
  • Posts: 2686
drillers
« on: September 17, 2015, 05:26:11 PM »
When someone hands you a drill sheet, you see the numbers for the span, and it's not marked "cut" or "true" span......what do you do?

I'm just wondering cause a friend had his ball drilled by another shop outside of town and the new driller was handed my friends drill sheet and it's 1/4 long. my friend sent me a copy of drill sheet and his old driller didn't label it cut or true.

just wondering...
Logged
Does a round object have sides? I say yes, pizza has triangles..

aka addik since 2003

 

JustRico

  • Hero Member
  • *****
  • Posts: 2652
Re: drillers
« Reply #1 on: September 17, 2015, 06:01:48 PM »
Look at a bowling ball that fits...eliminate confusion
Logged
Co-author of BowlTec's END GAMES ~ A Bowler's COMPLETE Guide to Bowling; Head Games ~ the MENTAL approach to bowling (and sports) & (r)eVolve
...where knowledge creates striking results...
BowlTEc on facebook...www.iBowlTec.com

drillbit

  • Hero Member
  • *****
  • Posts: 672
Re: drillers
« Reply #2 on: September 17, 2015, 07:49:45 PM »
Agreed, but what if you ONLY have the drill sheet, and it's not specified anywhere on the sheet? I always label my drill sheets, so as to avoid confusion.


drillbit
Logged

JustRico

  • Hero Member
  • *****
  • Posts: 2652
Re: drillers
« Reply #3 on: September 17, 2015, 08:35:24 PM »
Refit why chance it at that point
Logged
Co-author of BowlTec's END GAMES ~ A Bowler's COMPLETE Guide to Bowling; Head Games ~ the MENTAL approach to bowling (and sports) & (r)eVolve
...where knowledge creates striking results...
BowlTEc on facebook...www.iBowlTec.com

Juggernaut

  • Hero Member
  • *****
  • Posts: 6498
  • Former good bowler, now 3 games a week house hack.
Re: drillers
« Reply #4 on: September 17, 2015, 08:47:24 PM »
 I would not drill until I knew what I was looking at.

 A blueprint always has precise measurements on it. Without them, it is merely a worthless piece of paper. A drill sheet without measurements and guidelines is just that. WORTHLESS!

 Give me cut-to-cut, or give me a ball that fits. Anything else is useless to me.
Logged
Learn to laugh, and love, and smile, cause we’re only here for a little while.

xrayjay

  • Hero Member
  • *****
  • Posts: 2686
Re: drillers
« Reply #5 on: September 17, 2015, 10:12:50 PM »
Thats what I thought...

Why would one drill a ball not knowing for sure....not even a phone call lol
Guy prolly sees a bowler not knowing much about drilling and suckers him for $$$. Shady

Now, my friends finger nail is pressing against inserts...
Logged
Does a round object have sides? I say yes, pizza has triangles..

aka addik since 2003

DynoLess Daddy

  • Sr. Member
  • ****
  • Posts: 369
Re: drillers
« Reply #6 on: September 18, 2015, 04:43:29 PM »
Depends on teh drill sheet. Some are marked for CTC, TTL and etc. Some only account for TTL. All in all. When in doubt ask or measure the ball again. I have seen spec sheets where the CTC is for the IT but wasnt marked nor was it clear about IT. Just had the bit size. A litte reasoning goes along way but depends. Some drillers dont want their exact items out. This way they force you to come bach ...iif your local.
Logged

JohnP

  • Hero Member
  • *****
  • Posts: 5819
Re: drillers
« Reply #7 on: September 18, 2015, 06:26:36 PM »
"Give me cut-to-cut, or give me a ball that fits. Anything else is useless to me."

Cut to cut by itself is too vague.  Is the customer using a slug, and what size?  A sleeve?  Or just maybe a drilled thumb hole?  You need full spans, then adjust for thumb treatment and grip thickness (or maybe there are a few throwbacks like me that use drilled finger holes).  --  JohnP
« Last Edit: September 19, 2015, 05:59:44 PM by JohnP »
Logged

Strapper_Squared

  • Hero Member
  • *****
  • Posts: 4231
Re: drillers
« Reply #8 on: September 19, 2015, 02:06:43 PM »
The only way I have ever filled out a drill sheet is with the total overall span.  Cut to cut means something different depend on whether grips are used or not...

I would never assume a drill sheet was cut to cut, unless it was specified.
Logged
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Pages: [1]
« previous next »