win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Axis Weight Drilling  (Read 2779 times)

Urethane Game

  • Hero Member
  • *****
  • Posts: 1304
Axis Weight Drilling
« on: February 09, 2004, 10:23:08 PM »
What are the ideal pin specs for this type of ball drilling?  I know I need low top but should I stick with shorter pins or longer pins?
Logged

 

channel surfer

  • Hero Member
  • *****
  • Posts: 2036
Re: Axis Weight Drilling
« Reply #1 on: February 10, 2004, 01:52:40 PM »
lower
--------------------
My Bowling Clinic Site: http://csbowling.vze.com

ASK A PRO:http://csbowling.vze.com/atp.shtml

www.bowlersdream.com - save an additional $3 off any $100 order by simply typing in CSB into the coupon code area at checkout.
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: Axis Weight Drilling
« Reply #2 on: February 10, 2004, 02:01:14 PM »
For axis leverage 3 3/8 is ideal, also bring dry backends and a ton of hand!

REgards,

Luckylefty
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

Urethane Game

  • Hero Member
  • *****
  • Posts: 1304
Re: Axis Weight Drilling
« Reply #3 on: February 10, 2004, 05:11:42 PM »
More of a pin axis either on a 3 or 2 piece urethane.
Logged

Urethane Game

  • Hero Member
  • *****
  • Posts: 1304
Re: Axis Weight Drilling
« Reply #4 on: February 10, 2004, 08:11:25 PM »
My experience with axis weight has been all with 3 piece balls like a Wine U Dot, Gold Dot and PC3.  In the past, I have tried to get the ball back as close to zero positive as possible.  

Balls with side weight close to 1 oz, like my Gold Dot originally, never got into a roll.  A few years back I had a UDot drilled axis but for whatever reason, higher top I think, the ball thumped.  I track high but it was never a problem with any of the other balls.  We compared it to my PC3 and there was no difference in hole position etc.

I am concerned because back in the day, I believe the hole size could be bigger in diameter.  So I am wondering if it is even possible to achieve the same reaction I did with axis weight with the bigger hole.

I appreciate your help.

Edited on 2/10/2004 9:07 PM
Logged

Urethane Game

  • Hero Member
  • *****
  • Posts: 1304
Re: Axis Weight Drilling
« Reply #5 on: February 11, 2004, 12:22:56 AM »
I will be drilling 3 piece Urethane or 2 piece Urethane.  Perhaps even a Beastmaster.  All balls will be high RG.  It isn't a matter of getting the ball to start up but rather to lay off on the back end.
Logged

BuddiesProShopcom - Bill

  • Sr. Member
  • ****
  • Posts: 494
Re: Axis Weight Drilling
« Reply #6 on: February 12, 2004, 07:28:00 AM »
I have a Beast Pearl with a pin out about 1" drill axis and it doesn't do much, but other balls with longer pins will get more turn at the breakpoint.
--------------------
Thanks
Bill
BuddiesProShop.com
"The Place All Bowlers Shop"
Logged
Thanks
Bill
BuddiesProShop.com
"The Place All Bowlers Shop"
Pages: [1]
« previous next »