win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: When on high friction lanes...  (Read 7319 times)

mrwizerd

  • Sr. Member
  • ****
  • Posts: 450
When on high friction lanes...
« on: June 22, 2020, 10:09:43 AM »
...what layouts and equipment do you prefer to use, e.g. pin over/under, surface, etc?

I tried doing Google searches and only found definitions for high friction lanes.
Logged

 

TWOHAND834

  • Hero Member
  • *****
  • Posts: 4350
Re: When on high friction lanes...
« Reply #1 on: June 22, 2020, 01:19:14 PM »
Quote from: mrwizerd on June 22, 2020, 10:09:43 AM
...what layouts and equipment do you prefer to use, e.g. pin over/under, surface, etc?

I tried doing Google searches and only found definitions for high friction lanes.

For me I go with lower end equipment and older balls I have in the closet that I used back 15 years ago like a Dry Heat, Green Gargoyle, and G3 Gryphon.  I use my favorite layouts which are typically 5 inch pin to PAP and always have one ball on hand with the pin at 2 inches from my PAP.  Me being a little rev dominate it is difficult for me to use high end equipment or even anything more recent like a Gamebreaker 2 because it will force me deeper in to the lane than I want to be right out of the gate.  I would rather be outside of 3rd arrow and closer to 2nd arrow if possible.  I have a Deep Freeze which allows me to straighten my angles.  But other newer balls that would work well for me would be like a Messenger, Beast, Rhino, and Turbo and maybe even the IQ Tours due to its low flaring core.
Logged
Steven Vance
Former Pro Shop Operator
Former Classic Products Assistant Manager

Jesse James

  • Hero Member
  • *****
  • Posts: 3613
Re: When on high friction lanes...
« Reply #2 on: June 22, 2020, 02:24:42 PM »
Quote from: TWOHAND834 on June 22, 2020, 01:19:14 PM
Quote from: mrwizerd on June 22, 2020, 10:09:43 AM
...what layouts and equipment do you prefer to use, e.g. pin over/under, surface, etc?

I tried doing Google searches and only found definitions for high friction lanes.

For me I go with lower end equipment and older balls I have in the closet that I used back 15 years ago like a Dry Heat, Green Gargoyle, and G3 Gryphon.  I use my favorite layouts which are typically 5 inch pin to PAP and always have one ball on hand with the pin at 2 inches from my PAP.  Me being a little rev dominate it is difficult for me to use high end equipment or even anything more recent like a Gamebreaker 2 because it will force me deeper in to the lane than I want to be right out of the gate.  I would rather be outside of 3rd arrow and closer to 2nd arrow if possible.  I have a Deep Freeze which allows me to straighten my angles.  But other newer balls that would work well for me would be like a Messenger, Beast, Rhino, and Turbo and maybe even the IQ Tours due to its low flaring core.

And there you have it! He pretty much covered all the areas! I like using older equipment because of the milder coverstocks! 2" pin to pap works fantastically and gives one a nice arc to the pocket. I also use a lot of entry level balls for this purpose as well. My favorite is a Scout Reactive with surface and a mild arc drilling. Messenger, Beast, Rhino, Twist, Turbo, or the Storm tropical line is good for this also!
Logged
Some days you're the bug....some days you're the windshield...that's bowling!

Impending Doom

  • Hero Member
  • *****
  • Posts: 6288
Re: When on high friction lanes...
« Reply #3 on: June 22, 2020, 08:02:55 PM »
When I see high friction lanes, I tend to look at the pattern and go from there. If it's a house shot, you want to use slower response balls, with either a little surface or a slip agent, depending on volume. Places with guardian or really beat up mids, slip agent. I also use a larger val angle to tighten up the flare. Some of the best balls I had for that use case was a Stinger 2 piece pearl 5.5*65 with control it on it. More recently, I liked my X 5*65 to control motion. If I was going to choose a ball right now to get me out of trouble, I'd probably try a Venom Recoil 30*5.5*65 to get it to hook set and adjust the cover accordingly.
Logged

Good Times Good Times

  • Hero Member
  • *****
  • Posts: 6462
  • INTJ Personality
Re: When on high friction lanes...
« Reply #4 on: June 22, 2020, 08:44:18 PM »
I guess it depends on where the hook is.....and go from there.
Logged
GTx2

mrwizerd

  • Sr. Member
  • ****
  • Posts: 450
Re: When on high friction lanes...
« Reply #5 on: June 23, 2020, 08:33:14 AM »
Thank you everyone for your thoughts, insights, advice, etc, it sounds like I am on the right path.

I have a tournament coming up (on high friction lanes), I have been thinking of taking an IQ Solid and IQ Emerald, but I've also been looking at the Hustles INK, 3TP, and RAP.

Most of my layouts, I believe, have a 5" pin-to-pap, the next time I'm at the pro shop I will discuss a 2" pin-to-pap layout with them.

Thank you again.
Logged

TDC57

  • Hero Member
  • *****
  • Posts: 1273
Re: When on high friction lanes...
« Reply #6 on: June 23, 2020, 09:17:31 PM »
Two words: Motiv Thrill!!!
Logged

leftybowler70

  • Hero Member
  • *****
  • Posts: 1710
Re: When on high friction lanes...
« Reply #7 on: June 23, 2020, 09:55:15 PM »
Quote from: TDC57 on June 23, 2020, 09:17:31 PM
Two words: Motiv Thrill!!!

Agreed; Have this ball for dryer lanes, and high friction conditions. Great piece.
Logged
Pages: [1]
« previous next »