win a ball from Bowling.com

Author Topic: General track question...  (Read 3243 times)

islenmetfan4life

  • Sr. Member
  • ****
  • Posts: 476
General track question...
« on: January 26, 2014, 10:12:41 AM »
I need some insight on a few things...My girlfriend tracks over her thumbhole on every shot.. the first flare rings end up about 1-2 inches from her fingers though. her layouts are really strong, usually pin right of or below/right of the ring with weight holes (I don't understand this one but she gets free equipment and drilling from her school team), but she even rolls over the thumb with her plastic ball without intentionally trying to flatten out her wrist. Im not sure of her pap, but I'm going to have her get it measured this week. obviously she's unable to get any sort of backend and has a lot of inconsistency and lack of trust in her equipment and her game.

Does this mean she is a full roller, or do full rollers track over both the thumb and fingers? I don't fully know what full roller means, if someone could shed some insight on this for me it would be appreciated. What causes her track to be like this? Should she be using different/specific types of layouts? Or is her problem mainly with her release, and should this be corrected first? Thanks for the input

 

matskojd

  • Jr. Member
  • **
  • Posts: 58
Re: General track question...
« Reply #1 on: January 26, 2014, 10:58:35 AM »
I recently got a ball and it rolled over tge thumb. I am a full roller which is track close to the fingers. Turned out to be a missed marked ball where the pin was in wrong spot. If she is a full roller her track would be next to fingers and close to thumb hole. My pin position is always slightly to the right and above my ring finger. So going off what you are saying it sounds like her ball may be layed out wrong for her. The weight hole should pull her track away from the thumb hole. So you could also try going with a bigger weight hole. Hope that helps

JustRico

  • Hero Member
  • *****
  • Posts: 2652
Re: General track question...
« Reply #2 on: January 26, 2014, 12:22:56 PM »
It's a full roller you should lay them out accordingly...it's abt controlling the flare to avoid the gripping holes
Co-author of BowlTec's END GAMES ~ A Bowler's COMPLETE Guide to Bowling; Head Games ~ the MENTAL approach to bowling (and sports) & (r)eVolve
...where knowledge creates striking results...
BowlTEc on facebook...www.iBowlTec.com

MI 2 AZ

  • Hero Member
  • *****
  • Posts: 8157
Re: General track question...
« Reply #3 on: January 26, 2014, 04:00:48 PM »
Islenmetfan4life,

A full roller will track (for RH) left of the finger holes and right of the thumb hole.  See link for picture:

http://members.tripod.com/tips_4_tenpin/coaching/Roll/basics_of_grip_and_roll.htm

Tracking over the thumb means either the ball is not drilled properly (pin in wrong location) or the bowler may not be releasing the ball properly for the full roller.

Most manufacturers have full roller layouts available, here are a couple samples:
http://d1msaulk40dheh.cloudfront.net/523-bb_asymmetric-symmetric-drilling_instructions.pdf

http://www.stormbowling.com/drill-specs/Storm_symmetrical_DI_lr.pdf

Notice the pin is located left of the thumb hole.


_________________________________________
Six decades of league bowling and still learning.

ABC/USBC Lifetime Member since Aug 1995.

islenmetfan4life

  • Sr. Member
  • ****
  • Posts: 476
Re: General track question...
« Reply #4 on: January 27, 2014, 08:05:49 AM »
Islenmetfan4life,

A full roller will track (for RH) left of the finger holes and right of the thumb hole.  See link for picture:

http://members.tripod.com/tips_4_tenpin/coaching/Roll/basics_of_grip_and_roll.htm

Tracking over the thumb means either the ball is not drilled properly (pin in wrong location) or the bowler may not be releasing the ball properly for the full roller.

Most manufacturers have full roller layouts available, here are a couple samples:
http://d1msaulk40dheh.cloudfront.net/523-bb_asymmetric-symmetric-drilling_instructions.pdf

http://www.stormbowling.com/drill-specs/Storm_symmetrical_DI_lr.pdf

Notice the pin is located left of the thumb hole.




This is helpful.. she has a really high track and yesterday when we bowled she changed her release slightly and the flare lines weren't clipping the thumb... I definitely think it's a mechanics issue, but she definitely needs better layout choices. Thanks