win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: mo pinnel double thumb question  (Read 4427 times)

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
mo pinnel double thumb question
« on: January 28, 2015, 10:57:09 AM »
i want to test the double thumb layout on a bowling ball, but im still confused on how to do it. if their were a video of how to do it, id love to try it, but i dont want to mess up the double thumb and have the ball be crap. i have a fairly good understanding of dual angle layouts, but cant seem to understand how to find that first angle, ive been to many different websites trying to understand it and still cant do it, any help would be appreciated in advance...if it helps, my pap is 4 13/16 horizontal and 1 1/8 vertical
Logged

 

SVstar34

  • Hero Member
  • *****
  • Posts: 5461
Re: mo pinnel double thumb question
« Reply #1 on: January 28, 2015, 11:13:32 AM »
The first angle (drill angle) is created by connecting the line through the pin&psa with a line from the pap to pin. The angle created is the drill angle
Logged

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #2 on: January 28, 2015, 11:20:02 AM »
wouldnt it be different from ball to ball though if your looking at a predrilled ball?
Logged

ImBackInTheGame

  • Hero Member
  • *****
  • Posts: 1022
Re: mo pinnel double thumb question
« Reply #3 on: January 28, 2015, 11:42:56 AM »
Quote from: TeeP Nade on January 28, 2015, 11:20:02 AM
wouldnt it be different from ball to ball though if your looking at a predrilled ball?

You cannot just add a Double Thumb to a pre-drilled ball and expect it to react as it is intended.
Logged

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #4 on: January 28, 2015, 11:50:34 AM »
Quote from: ImBackInTheGame on January 28, 2015, 11:42:56 AM
Quote from: TeeP Nade on January 28, 2015, 11:20:02 AM
wouldnt it be different from ball to ball though if your looking at a predrilled ball?

You cannot just add a Double Thumb to a pre-drilled ball and expect it to react as it is intended.


thats what i figured, thats y im trying to figure out how to determine that first angle, on all the info i c on how to do double thumb, it says take a prexisting ball   
"The Double Thumb Layout instructions tell us to use an existing ball, mark the PAP and measure the required VAL angle and measure a point 4″ from the PAP. This is our “pretend” Pin. " what is the "required VAL angle" im on this websitehttp://kellytehuna.com/blog/2010/09/22/mo-pinels-double-thumb-layout-explained/ trying to understand it
Logged

tommymo

  • Hero Member
  • *****
  • Posts: 821
Re: mo pinnel double thumb question
« Reply #5 on: January 28, 2015, 12:00:34 PM »
30° is the Val w/4" pin to pap. Mark the pretend PSA 1/2" right (if you're rh)from the thumb hole. Draw a line connecting the pretend pin to the pretend PSA. That is your drill angle.
Logged
Tom M.

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #6 on: January 28, 2015, 12:12:39 PM »
got it, thanks alot guys! major help, hopefully i'll b able to get a good reaction outta it :)
Logged

tommymo

  • Hero Member
  • *****
  • Posts: 821
Re: mo pinnel double thumb question
« Reply #7 on: January 28, 2015, 12:38:26 PM »
Remember to target balls with a 4-6" pin and low top weight before drilling. Especially with you're vertical pap coordinates.
Logged
Tom M.

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #8 on: January 28, 2015, 01:13:56 PM »
got a 3.25 inch pin on one of my balls, and i forget what the top weight is on it, dont have the box by it, if that dosnt work, i'll find one with a 4-6 inch pin to test it on, when drilling, should i drill the fingers shallow to put more weight on top, or deep to lessen it?
Logged

tommymo

  • Hero Member
  • *****
  • Posts: 821
Re: mo pinnel double thumb question
« Reply #9 on: January 28, 2015, 01:17:57 PM »
I would go 2" to start. Depends where the weight is before drilling. You want thumb weight so that you can put in the balance hole. So if you have finger weight before drilling (depending how much there is) you'll want to drill the fingers deeper. The best bet is to have a longer pin and 1-2oz of top weight. The longer pin should have the CG landing on or below the midline.
Logged
Tom M.

JohnP

  • Hero Member
  • *****
  • Posts: 5819
Re: mo pinnel double thumb question
« Reply #10 on: January 28, 2015, 01:25:28 PM »
Logged

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #11 on: January 28, 2015, 01:30:12 PM »
Quote from: tommymo on January 28, 2015, 01:17:57 PM
I would go 2" to start. Depends where the weight is before drilling. You want thumb weight so that you can put in the balance hole. So if you have finger weight before drilling (depending how much there is) you'll want to drill the fingers deeper. The best bet is to have a longer pin and 1-2oz of top weight. The longer pin should have the CG landing on or below the midline.
my next ball i'll request a long pin, as for this ball, it's a spike xout(color mismatch) i figured hey it only cost me $45 y not give it a shot haha
Logged

TeeP Nade

  • Full Member
  • ***
  • Posts: 136
Re: mo pinnel double thumb question
« Reply #12 on: January 28, 2015, 01:45:22 PM »
question for everyone...would it be ok to do the double thumb layout on an aysmetrical ball as well as a symetric?
Logged

tommymo

  • Hero Member
  • *****
  • Posts: 821
Re: mo pinnel double thumb question
« Reply #13 on: January 28, 2015, 01:48:57 PM »
Yes, works on both
Logged
Tom M.
Pages: [1]
« previous next »