win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: need drilling help quick!  (Read 1575 times)

fishbowler

  • Hero Member
  • *****
  • Posts: 1259
need drilling help quick!
« on: December 30, 2004, 01:28:00 AM »
got a depth charge ready to be punched up.

want a clean start with a strong midlane and controlled backend arc.

ball has a 4 inch pin.  was thinkinh pin right under bridge or ring, cg down by thumb and out to right.  most likely a wt whole in thumb positive quadrant.  would this give me the desired reaction I am looking for.

I am needing this ball for aths when the track begins to get played on and have to mover in just a little and bump into the track.
Logged

 

fishbowler

  • Hero Member
  • *****
  • Posts: 1259
Re: need drilling help quick!
« Reply #1 on: December 30, 2004, 09:28:40 AM »
my pap is 5 in oveer and 1/2 inch up.
Logged

fishbowler

  • Hero Member
  • *****
  • Posts: 1259
Re: need drilling help quick!
« Reply #2 on: December 30, 2004, 10:00:33 AM »
he wants to drill all balls label.
Logged

Strapper_Squared

  • Hero Member
  • *****
  • Posts: 4231
Re: need drilling help quick!
« Reply #3 on: December 30, 2004, 12:39:40 PM »
yes...label will give arcing backend, but not a strong midlane...  I would say a 45 degree layout with roughly 4" pin to PAP.  The lower the pin is placed, the earlier the ball will start up, but be careful about placing it too low as sometimes this can cause the ball to flare over the fingers (with the relatively high track).  Should be alright to place the pin just under the fingers though.

S^2
--------------------
=-=-=-=-=-=-=-=-=-=-=-=-=-=

I think it's the duty of the comedian to find out where the line is drawn and cross it deliberately.

George Carlin
Logged
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Brickguy221

  • Hero Member
  • *****
  • Posts: 9918
Re: need drilling help quick!
« Reply #4 on: December 30, 2004, 12:40:39 PM »
I have a Depth Charge with pin under RF and RAD in the strong position. (ball doesn't have a marked RAD, but check CG and if accurate, draw a line 6 3/4" from pin thru CG to a point 6 3/4" down) has a weight hole on VAL. This ball has a 2 1/4" pin and gets thru the midlane very cleanly and has a hard hook on the back-end. It isn't an arc, but it isn't a flip either, just a hard turn and drive.
Logged
"Whenever I feel the urge to exercise I lie down until the feeling passes away"

channel surfer

  • Hero Member
  • *****
  • Posts: 2036
Re: need drilling help quick!
« Reply #5 on: December 30, 2004, 02:40:19 PM »
quote:
I would say a 45 degree layout with roughly 4" pin to PAP.  

S^2
--------------------
=-=-=-=-=-=-=-=-=-=-=-=-=-=

I think it's the duty of the comedian to find out where the line is drawn and cross it deliberately.

George Carlin


I concur.
--------------------
www.csbowling.vze.com

HA HA!!1 IM USING THE INTERNET!!11
Logged

iommifan

  • Hero Member
  • *****
  • Posts: 611
Re: need drilling help quick!
« Reply #6 on: December 30, 2004, 02:44:27 PM »
I know someone with a Depth Charge drilled full leverage and it is a very strong ball. Skids probably half the way and makes a sharp move. Very strong ball.
Logged
Pages: [1]
« previous next »