Author Topic: Router depth (Read 4094 times)

mbrown205 · « **on:** August 19, 2014, 05:35:14 PM »

What's the best depth for using a router for plug cutting? Also would you recommend resurfacing after cutting plug, or just sanding on a ball spinner?

itsallaboutme · « **Reply #1 on:** August 19, 2014, 05:54:12 PM »

You need to adjust the router depth on every ball. Resurfacing is up to you.

JohnP · « **Reply #2 on:** August 20, 2014, 05:04:58 PM »

I assume you're using the router with a shield. I adjust mine for each ball by setting the bit height so I can see just a sliver of light between the bit and the ball. Be sure the setting doesn't change when you lock the bit down. -- JohnP

mbrown205 · « **Reply #3 on:** August 20, 2014, 05:10:22 PM »

The shield is what the vacuum hooks up to correct?

JohnP · « **Reply #4 on:** August 21, 2014, 04:33:24 PM »

Yes, it's made out of clear plastic or plexiglass. -- JohnP

Rightycomplex · « **Reply #5 on:** August 22, 2014, 10:07:24 AM »

It is best to have a plug cutter. Every ball is different. On my press, even at 0-0, some balls will be off so adjust accordingly. I take the cutter to the ball and adjust the table so that there are no gaps.

When using a router, which I have very little experience with, I texted it the same as the plug cutter, adjusting from ball to ball. Resurfacing is the choice of the bowler. I use grill screen to clean up the plug work and have a set of abralon pads to smooth out the work. I'll then take the ball to box.

EFFEN 10 · « **Reply #6 on:** August 22, 2014, 07:31:40 PM »

Quote from: Rightycomplex on August 22, 2014, 10:07:24 AM

It is best to have a plug cutter. Every ball is different. On my press, even at 0-0, some balls will be off so adjust accordingly. I take the cutter to the ball and adjust the table so that there are no gaps.

X2. I also use my plug cutter to zero my table. I check it every couple of weeks.

itsallaboutme · « **Reply #7 on:** August 22, 2014, 09:23:46 PM »

There is no reason to go out and buy a plug cutter if you don't have one and you have a router. You can do all the plug work you need to do with a router.

Rightycomplex · « **Reply #8 on:** August 22, 2014, 09:28:57 PM »

Quote from: itsallaboutme on August 22, 2014, 09:23:46 PM

There is no reason to go out and buy a plug cutter if you don't have one and you have a router. You can do all the plug work you need to do with a router.

True. I just said it's best to have one. Saves time, energy, and effort. I can cut down a fully plugged ball in a matter of a couple seconds and have it surfaced and ready for drilling in 2 mins. A plug cutter can pay for itself in 2 nights in the shop but that's just depends on how hard you want to work and how much time you want to save. Some guys get really good at using a router, I'm not one.

JohnP · « **Reply #9 on:** August 23, 2014, 08:31:15 PM »

I would love to be able to use a plug cutter but the shroud on my sidewinder isn't big enough for one. I have one I bought used without realizing I couldn't use it. If anyone is interested, it has a MT 2 shaft (you can buy an adapter to straight shaft), doesn't look like it's ever been used, and I'll sell it for $50 + actual shipping cost. PM me if interested. -- JohnP

Author Topic: Router depth (Read 4094 times)

mbrown205

Router depth

itsallaboutme

Re: Router depth

JohnP

Re: Router depth

mbrown205

Re: Router depth

JohnP

Re: Router depth

Rightycomplex

Re: Router depth

EFFEN 10

Re: Router depth

itsallaboutme

Re: Router depth

Rightycomplex

Re: Router depth

JohnP

Re: Router depth