Post by: chitown on April 12, 2007, 01:26:16 AM
--------------------
HAMMER NO MERCY is Un-freaking real! Using this ball is like cheating!
Post by: A K A on April 12, 2007, 09:31:47 AM
Post by: monstercrank on April 12, 2007, 09:32:01 AM
--------------------
Scott Fello's Striking Results Proshop
---------------------------------
If guns kill people then spoons made Rosie O'Donnell fat!
Edited on 4/12/2007 9:31 AM
Post by: dizzyfugu on April 12, 2007, 09:36:16 AM
When the oil is (too) long, though, say 40'+, I'd rather use a light load particle ball like my trusty Eliminator or XXcel. For me and my lower speed, it is a head oil question - as long as there is enough oil the particles will float down and smooth out the back end reaction, but there is the danger of burnout once the heads fall apart and I cannot move my line (generally deeper).
An in-between option for me is my old polished Eraser Particle Pearl which has very good length and also a smooth breakpoint - but I do not have it in my bag too often anymore. But for a player with more speed than me, this could be a ticket to control the flying back end.
--------------------
DizzyFugu - Reporting from Germany
Confused by bowling? Check out BR.com's vault of wisdom: the FAQ section (http://"http://www.ballreviews.com/Forum/Replies.asp?TopicID=74110&ForumID=16&CategoryID=5")
Post by: Strider on April 12, 2007, 09:37:18 AM
2) Anything rolly with some surface to use some energy before it hits the dirt.
--------------------
Penn State Proud
Special thanks to Dynothane, Visionary, and Lane#1 for donations to the Ballreviews Get Together.
Ron Clifton's Bowling Tip Archive (http://"http://www.bowl4fun.com/ron/roncarchive.htm")
Post by: JohnP on April 12, 2007, 10:51:41 AM
Post by: Goof1073 on April 12, 2007, 11:54:38 AM
Our house went knocked back on their length / buff a while back and I found that I had a great look with my old Pure Energy (high flaring dull particle solid). One short patterns I like weak balls like a Hot Rod Hybrid with a more agressive drilling and some surface.
Either way surface is your friend to control the down lane reaction.
--------------------
-Chris: DJ's Pro Shop : Auburn, MA
Post by: Joe Jr on April 12, 2007, 12:03:08 PM
--------------------
Back were I belong...with Roto Grip.
My Vid (http://"http://youtube.com/user/BLefty")
Banned under the user name Richard Cranium
Formerly Brunswick Lefty
Post by: Ragnar on April 12, 2007, 12:20:18 PM
quote:
Solid particle or a solid resin with a lower RG, drilled with a short pin to PAP, or even a true pin axis drilling. Does the trick for me every time.
Yep.
--------------------
"I do desire that we may be better strangers." Willie the Shake, As You Like it(III,ii)
"I'm capable of being just as sorry as you are, Dimitri."
Post by: LuckyLefty on April 12, 2007, 12:29:05 PM
REgards,
Luckylefty
--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Post by: C-G ProShop-Carl on April 12, 2007, 02:03:50 PM
pin on VAL 2 inches above PAP CG towards center of the palm.
SMOOTH...but head oil is needed!
--------------------
Carl Hurd
C-G Pro Shop (owner/operator)
Youngstown Ohio
Tag Team Member #1
TAG TEAM COACHING!!!!!!/Co-Founder
Post by: Fluff E Bunnie on April 12, 2007, 02:03:51 PM
quote:
2 words "Purple Thunderstruck"
Thats all ya need on that condition !
Huzah! I will say whenever the backends are flying I just move left with that ball and get it out there.
--------------------
Thunderstruck $olid
Post by: Ishmael on April 12, 2007, 02:12:45 PM
quote:
I like a ball with a 4 inch pin.....
pin on VAL 2 inches above PAP CG towards center of the palm.
SMOOTH...but head oil is needed!
I have an old Revolution Vengeance with the pin on the VAL 1.5" above the PAP, cg swung back toward the grip center, and a big x-hole just below the PAP, cover dulled to about 600 grit. Awesome on flying backends. It just arcs to the pocket when it finds friction and hits great. Caution: must have head oil.
Post by: DON DRAPER on April 12, 2007, 04:40:33 PM