Author Topic: Plugging a ball with vise IT installed (Read 7527 times)

lsf_21 · « **on:** March 08, 2013, 01:56:12 AM »

I have a ball that has the vise IT in it that needs to be plugged. Is the only way to get it out to drill it out?

lsf_21 · « **Reply #1 on:** March 08, 2013, 02:04:42 AM »

Or would it be easiest to just find a vise IT slug and have it drilled to fit?

Rightycomplex · « **Reply #2 on:** March 08, 2013, 07:14:19 AM »

If you dont use the IT system then you could drill it out, plug the hole and make it fit you specs. If you drill an IT slug for yourself, you should to drill it in every ball, otherwise it doesnt justify the purchase.

bigz · « **Reply #3 on:** March 08, 2013, 08:17:54 AM »

It's easier to make an IT slug and deal with the fingers by plugging or drilling them.i had gotten 3 balls in a trade and had my proshop guy drill the fingers for grips and made me a thumb slug.

BallReviews-Removed0385 · « **Reply #4 on:** March 08, 2013, 08:19:13 AM »

Unless the new pitches are the same I'd suggest removing the whole thing.

One other note to consider is when plugging a large mass like that I'd do it 1/2 at a time. If you try to plug it all at once your chances of cracks at the top are much greater, because with that much plug material it gets too hot too quickly.

lsf_21 · « **Reply #5 on:** March 08, 2013, 08:41:17 AM »

It just looks like a lot of ball to have to drill out to plug it.

lsf_21 · « **Reply #6 on:** March 08, 2013, 08:42:08 AM »

and I do wish my pro shop used vise IT or Switch Grips. He cant justify the purchase since there are so few that would install it.

ccrider · « **Reply #7 on:** March 08, 2013, 09:39:29 AM »

Switch grip starter kit is less than 500 bucks. Much cheaper than Vise. He can call and talk to the lady there Eleanor or Addelien and they may cut him a deal.

PowrKoil17 · « **Reply #8 on:** March 16, 2013, 11:28:08 AM »

You can buy the just the slug for the IT on ebay for about $10 and have your local driller drill the slug, that's what I did.

lsf_21 · « **Reply #9 on:** March 16, 2013, 03:40:26 PM »

Where? I cant find one.

PowrKoil17 · « **Reply #10 on:** March 16, 2013, 07:50:03 PM »

http://www.ebay.com/itm/Vise-IT-1-3-8-Set-Ball-It-Slug-It-Sleeve-Mollies-/180583677156?pt=LH_DefaultDomain_0&hash=item2a0ba03ce4

go to this ebay link and email premierbowlersproshop and tell the guy your size of slug you need and that you need the slug only. he will invoice you through paypal, I believe mine was an 1 1/4 slug shipped to my door for $10. my driller punched it up for free.

lsf_21 · « **Reply #11 on:** March 16, 2013, 08:05:28 PM »

Thanks man.

StickZ · « **Reply #12 on:** March 16, 2013, 08:54:32 PM »

dont you need all the tools needed to install a IT?

Author Topic: Plugging a ball with vise IT installed (Read 7527 times)

lsf_21

Plugging a ball with vise IT installed

lsf_21

Re: Plugging a ball with vise IT installed

Rightycomplex

Re: Plugging a ball with vise IT installed

bigz

Re: Plugging a ball with vise IT installed

BallReviews-Removed0385

Re: Plugging a ball with vise IT installed

lsf_21

Re: Plugging a ball with vise IT installed

lsf_21

Re: Plugging a ball with vise IT installed

ccrider

Re: Plugging a ball with vise IT installed

PowrKoil17

Re: Plugging a ball with vise IT installed

lsf_21

Re: Plugging a ball with vise IT installed

PowrKoil17

Re: Plugging a ball with vise IT installed

lsf_21

Re: Plugging a ball with vise IT installed

StickZ

Re: Plugging a ball with vise IT installed