win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Used ball with weird drilling  (Read 1737 times)

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Used ball with weird drilling
« on: August 14, 2006, 03:51:04 PM »
Just got an X-Factor ReLoaded with the following drill, for a right-hander: CG kicked LEFT of the grip (it's below and to the left of the middle finger), pin above and to the LEFT of the middle finger. RAD is below and to the right of the thumb hole, where you'd expect it.

What's this drilling going to do for me? I'm right-handed.

Jess
Logged

 

Traumatize

  • Hero Member
  • *****
  • Posts: 810
Re: Used ball with weird drilling
« Reply #1 on: August 14, 2006, 11:56:03 PM »
Depending what your axis point is, I would say it will create superb length with a very angular backend reaction.  Re-Loaded is a skid-flippy ball by nature, so this drilling will only add to that reaction.
--------------------
Buffalo bowlers are the best all around in the country.

AMF Thruway Lanes Pro Shop employee, and I have no problem saying that I'm Officially a Ball Junkie.
Logged

DanH78

  • Hero Member
  • *****
  • Posts: 3913
Re: Used ball with weird drilling
« Reply #2 on: August 14, 2006, 11:57:38 PM »
How high and how far left is the pin?  

High pin gives you length, MB right of thumb gives strong backend.
--------------------
What are you gonna do?  Beat me with your Jesus stick?
Logged
#10

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Re: Used ball with weird drilling
« Reply #3 on: August 15, 2006, 12:03:20 AM »
The ball has about a 2.5-inch pin, so the pin is about 10:30 or 11 o'clock above left of the middle finger, while the CG is about 7:30 or 8 o'clock below left of the middle finger. Both items are about 2 inches away from the middle finger.

What someone did, using the same basic thumbhole, was to swap the fingers from the standard side of the pin and CG (i.e., pin above and right of ring, CG below and right of ring) to the other side of the pin and CG, and left the MB in the same place.

I'm worried that I might thump the middle finger with this drill. I was also kind of wanting to sand this ball a little -- I have another ReLoaded that I was planning to polish and set up for skid/flip -- but I guess I won't be doing that.

Jess
Logged

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Re: Used ball with weird drilling
« Reply #4 on: August 15, 2006, 12:40:19 AM »
Anyone else have experience with this drilling for a righty? What challenges do I face with it?

Jess
Logged

Re-Evolution

  • Hero Member
  • *****
  • Posts: 2080
Re: Used ball with weird drilling
« Reply #5 on: August 15, 2006, 02:43:14 AM »
I had an original X-Factor that was drilled similar pin was high over middle finger with the RAD about 1.5" right of the thumb CG was slightly right of GC with  a small weight hole drilled to bring it to 0. I absolutely loved it at the center I was bowling in at the time. The pattern was a 44' christmas tree medium with beat up heads. The drilling completely ignored the front 35' or so and pushed very easily with a strong flip/arc.
A drilling like that shouldn't flare over the middle finger cause the bowtie should be quite high. Some people will clip the thumb when a ball has negative weight.
I would imagine that the previous owner was a high rev low tracker as was the previous owner of the X-Factor I had.
--------------------

*****Re-Evolution*****
Evolve to a smarter game.

www.Bowling-Info.com
BR.com's unofficial FAQ section

Logged

CG_Matters

  • Sr. Member
  • ****
  • Posts: 359
Re: Used ball with weird drilling
« Reply #6 on: August 15, 2006, 08:20:41 AM »
This drilling is about how 5x5 looks for me.  I had it in a Ravage II.  This ball went for MILES and then went hard enough around the corner that it almost came back to me.

So what they've given you is correct....mega skid and lots of backend.
Logged

kmanestor22

  • Hero Member
  • *****
  • Posts: 969
Re: Used ball with weird drilling
« Reply #7 on: August 17, 2006, 11:17:35 PM »
quote:
The ball has about a 2.5-inch pin, so the pin is about 10:30 or 11 o'clock above left of the middle finger, while the CG is about 7:30 or 8 o'clock below left of the middle finger. Both items are about 2 inches away from the middle finger.

What someone did, using the same basic thumbhole, was to swap the fingers from the standard side of the pin and CG (i.e., pin above and right of ring, CG below and right of ring) to the other side of the pin and CG, and left the MB in the same place.

I'm worried that I might thump the middle finger with this drill. I was also kind of wanting to sand this ball a little -- I have another ReLoaded that I was planning to polish and set up for skid/flip -- but I guess I won't be doing that.

Jess


If you're a high tracker, it will thump.  That would put the pin around 6 inches from PAP.  You could fix it with a weight hole, but the CG is already on the negative side so I would say plug it.
--------------------
Where is the bait?  I'm goin' to jail!!! - Chocolate GAYzer
Logged
Pages: [1]
« previous next »