win a ball from Bowling.com
« previous next »
Pages: 1 [2]

Author Topic: Looking to Standardize on a single Layout  (Read 10110 times)

bradl

  • Hero Member
  • *****
  • Posts: 1660
Looking to Standardize on a single Layout
« on: October 06, 2020, 08:23:25 PM »

This may be a hard question to ask, but I'll ask it anyway.

I'm looking now to standardize my layout across all of the balls I have, but I'm more wondering about how a given layout would work (I'm tired of just telling the PSO "pin up, CG kicked out!" and not knowing the exact layout), and I'm looking for insights into how any of you would think a layout would work.

And of course, it doesn't help that the last ball I had punched up was from 4 years ago, with the Scandal Pearl, and I'm not too well versed in trying to reverse engineer/figure out a layout after the ball has been punched up..

With that, if I'm right handed, have a PAP of 5.25 over, 1.25 up, with a ball speed around 425rpm, how do you think that a 70x5x50 or a 70x4x50 layout or similar would roll? I'm seeing how someone with that same layout (with a 5" pin) is rolling that ball phenomenally, but has a 370-380rpm ball speed (slower than me).

Nothing that I see in the standard symmetric layout guides mention anything about how the ball is drilled up (dual-angle layout specs), so I can't tell how close the above would be to one of those on the symmetric sheets. Anyone have any ideas on how that layout would work with that speed and PAP?

BL.
Logged

 

DCNetBoy

  • Jr. Member
  • **
  • Posts: 76
Re: Looking to Standardize on a single Layout
« Reply #16 on: October 10, 2020, 11:09:45 AM »
Bradl,

May I make a simple suggestion that really helped me out in this same situation.  Let me explain…

Before the last year and a half ago, I used to be the guy who walked in the pro shop and did the same exact thing.  Although I knew the exact ball that I wanted, when it came to the layout of the ball, I would tell the ball driller where I wanted the location of the pin and mass bias, depending on the ball.

I did not fully understand the dual angle or pin buffer systems when it came to drilling the ball.  I just took my drillers word when it came to those things.  I knew the difference with pin up / pin down and how I wanted my ball to “look” in terms of the drilling.  When it came to RG and differential, I paid no attention to those things, simply because I knew what I wanted.  And for the most part, that method was successful for me.
 
However, here is where my suggestion comes in.  YouTube is best place to find instructional videos about the dual angle layout and pin buffer drilling systems.  In fact, check out the Storm, Radical, and Motiv videos “first”.  When you go to YouTube, do a search on “dual angle layouts” and watch EVERY video on the subject.  Then, watch them again until you understand them.  And then, take notes!  LOL.  The ones from Storm and Radical are absolutely excellent and helped me tremendously.  There are other videos as well, but start there.
 
I literally have learned so much over the past year and a half when it comes to ball reaction and layouts, that I can now walk into my pro shop and lay the balls out for myself.  Seriously.  The only thing that I can’t do is drill.  LOL.  I usually have my ball driller check my accuracy and then have him drill the ball.  Am I an expert now?  No, by no means.  However, I do now know exactly how ALL of my equipment is drilled and what the differences are.  And another benefit of it all is that I can’t blame the pro shop for a bad reaction.  LOL.   ;) 8)
 
Lastly for you, my suggestion to you would be to NOT purchase another ball or choose a layout until you fully understand what the numbers really mean, if you don't already.  You’re welcome in advance!  LOL!   :D  Peace! 
Logged
Pages: 1 [2]
« previous next »