win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Need to experiment  (Read 2587 times)

Doc Hollywood

  • Hero Member
  • *****
  • Posts: 1177
Need to experiment
« on: September 14, 2003, 04:56:36 AM »
I am looking to try something new in a drill pattern.  I am going to work on playing an inside line between 4th and 5th arrow.  Light short oil and carry down on the backends.

I am looking for a drill that will go fairly straight through the heads and then roll heavy in an arc (no snap).

I have plenty of revs and good speed.  Axis rotation is around 45-60 degrees and very little tilt.  

Planning on using a low rg medium flaring ball.  Most likely polished pearl reactive.

What are your thoughts
--------------------
Doc
Owner and Inventor of
DOC'S MAGIC BOWLING BALL ELIXIR
For more information click on the link below
http://home.comcast.net/~docsmagic/
or message me at:
http://Doc65@aol.com
Logged

 

T-GOD

  • Hero Member
  • *****
  • Posts: 2141
Re: Need to experiment
« Reply #1 on: September 14, 2003, 08:17:52 PM »
Doc, I would place the pin 6-6 1/4" from your PAP and kick the CG out. This will give you what you're looking for. =:^D
Logged

Doc Hollywood

  • Hero Member
  • *****
  • Posts: 1177
Re: Need to experiment
« Reply #2 on: September 14, 2003, 08:50:49 PM »
T-GOD - Thanks for the response.

How far out should I kick the cg?

Should I use a weight hole and where sould it be?

By the way the ball I am using has a 2 inch pin
--------------------
Doc
Owner and Inventor of
DOC'S MAGIC BOWLING BALL ELIXIR
For more information click on the link below
http://home.comcast.net/~docsmagic/
or message me at:
http://Doc65@aol.com
Logged

scotts33

  • Hero Member
  • *****
  • Posts: 8452
Re: Need to experiment
« Reply #3 on: September 14, 2003, 11:02:44 PM »
T-God--I'd also like to know more about this type of drilling.  What should we look for as far as pin placement and top weight?  My PAP is 4 7/8's over 1/2" up and a low tracker.  

Thanks,
Scott
Logged
Scott

T-GOD

  • Hero Member
  • *****
  • Posts: 2141
Re: Need to experiment
« Reply #4 on: September 14, 2003, 11:47:43 PM »
Personally, I think longer pins are better because the pin should be over the fingers. If not, it'll have more of a tendency to clip a finger. But, because you're cutting out the flare, you might be OK.

I would kick out the CG as much as possible. The more you kick it, the more the backend though. The weight hole can be anywhere, but I would put it on your axis. This will give you more of an arc.

Be careful with this drilling though. If you hit a strip of oil, the ball may not hook at all on the back.

The more you stay behind the ball with this drilling, the less it will hook and/or more it will have a tendency to roll out. The more you turn the ball, the quicker and more it will hook. =:^D
Logged

Doc Hollywood

  • Hero Member
  • *****
  • Posts: 1177
Re: Need to experiment
« Reply #5 on: September 16, 2003, 02:12:32 PM »
Thanks for the replys.

Plus40 - I only have a 2" pin out ball so going above the fingers is not really an option.  I do not not have to worry about the flare though.

BH - I have a silver streak pearl drilled 1:30 and a silver streak drilled 1:30 and another silver streak drilled 10:30.  I am going to punch up a V2 pearl like T-GOD said but I am going to put the pin under the middle finger and kick the cg out right and put a weight hole on the axis.  

I have a savage pearl drilled almost the same but with the weight hole in the thumb positive quadrant and has rolled well.  But it is a heavier weight ball and I am dropping weight.

--------------------
Doc
Owner and Inventor of
DOC'S MAGIC BOWLING BALL ELIXIR
For more information click on the link below
http://home.comcast.net/~docsmagic/
or message me at:
http://Doc65@aol.com
Logged
Pages: [1]
« previous next »