win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Question re: assymetrical Mass Bias placement  (Read 2008 times)

yeehayashi

  • Full Member
  • ***
  • Posts: 204
Question re: assymetrical Mass Bias placement
« on: November 10, 2009, 02:10:56 AM »
In an assymetrical ball, does the mass bias marker usually determine if a ball is set up for left-handed vs. right-handed players?  Reason I ask is that I have a Cell Pearl which has the MB marker offset to the left of the pin & cg.  This ball just doesn't seem to make the aggressive skid-flip move I've seen others get with this ball & what I was looking for with this ball.  I'm a righty with medium ball speed and revs.
Logged

 

kmanestor22

  • Hero Member
  • *****
  • Posts: 969
Re: Question re: assymetrical Mass Bias placement
« Reply #1 on: November 10, 2009, 10:53:05 AM »
Needs more info....PAP to pin, MB placement, weight hole placement if any....
--------------------
Where is the bait?  I'm goin' to jail!!! - Chocolate GAYzer
Logged

dizzyfugu

  • Hero Member
  • *****
  • Posts: 7606
Re: Question re: assymetrical Mass Bias placement
« Reply #2 on: November 11, 2009, 12:52:12 AM »
If the MB is in your track area, the ball's reaction becomes mellow. More mid lane read, less back end. In the worst case, with a high track, it can even flare backwards with a totally screwed reaction. But there are a lot of other opotential factors - a PAP of yours and maybe a picture of the drilled ball would help a lot with diagnosis.
--------------------
DizzyFugu - Reporting from Germany

Confused by bowling? Check out BR.com's vault of wisdom: the unofficial FAQ section
Logged
DizzyFugu ~ Reporting from Germany

the pooh

  • Hero Member
  • *****
  • Posts: 615
Re: Question re: assymetrical Mass Bias placement
« Reply #3 on: November 11, 2009, 07:44:57 AM »
CG to the left is better for most layouts for a right handed bowler. It allows you to swing the mb down and not need a weight hole. CG to the right is better for a left hander. Either alignment does not perform differently, just makes it easier for the driller to layout the ball. If your ball is not performing as you think it should,it is probably the wrong layout for you,where you bowl. Or,it could be as simple as aa surface adjustment. Surface accounts for about 70% of a ball's reaction.
--------------------
the pooh
Logged
the pooh

yeehayashi

  • Full Member
  • ***
  • Posts: 204
Re: Question re: assymetrical Mass Bias placement
« Reply #4 on: November 11, 2009, 01:22:30 PM »
Thanks for the feedback folks.  The pin placement is centered above the fingers and located 5+ inches from my PAP.  I get good length, but the ball just seems a little lazy on the backend and doesn't give me the skid-flip finish I expected.
--------------------
Spence Hayashi
Logged

DanH78

  • Hero Member
  • *****
  • Posts: 3913
Re: Question re: assymetrical Mass Bias placement
« Reply #5 on: November 11, 2009, 01:41:24 PM »
quote:
Thanks for the feedback folks.  The pin placement is centered above the fingers and located 5+ inches from my PAP.  I get good length, but the ball just seems a little lazy on the backend and doesn't give me the skid-flip finish I expected.
--------------------
Spence Hayashi


And where is the MB?  If the MB is to the track side of the thumb, then you are getting the reaction that should be expected.  If that's how it is currently drilled, plug it, keep the pin above the fingers, but move the MB to the other side of the thumb hole, that will give you a stronger backend reaction.  Just know that due to the CG being offset, you'll probably need a decent sized weight hole to get the statics legal.
--------------------
It IS next year!
Logged
#10

T-GOD

  • Hero Member
  • *****
  • Posts: 2141
Re: Question re: assymetrical Mass Bias placement
« Reply #6 on: November 12, 2009, 09:03:49 PM »
Personally, I like the CG to the right of the mb and pin. This tpye of ball is stronger in the midlane and better on an oilier condition. Is the mb to the left of your thumb..? This could be why the ball is lazy.

Also, check your statics, as they could add a little kick if used correctly. Meaning bottom weight, thumb weight and zero side weight will make the ball a bit more lazy. Adding more positive weights could help on drier conditions. =:^D =:^D
Logged
Pages: [1]
« previous next »