win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: How do you drill offset asyms  (Read 1260 times)

imjouster

  • Hero Member
  • *****
  • Posts: 643
How do you drill offset asyms
« on: November 11, 2006, 11:44:01 AM »
I have a friend that got a Track Xception from a closeout deal a while ago.  well this ball has probably the worst pin/cg/MB line I think I have ever seen.  Its a 1 inch pin, and it is literally in a "T" to the mass bias.  basically its like this

P CG


MB

We tried a drill with the MB on left side of thumb and it just did not roll well at all for him.  (fairly low rev, slow ball speed, high track, stroker).
I have heard of layouts where you draw a line 13.5" from the MB through the Pin and then use the spot you end up with as the MB???  Not sure if that would work or not as I'm not exactly a pro on Asyms.  basically if I can do this then I would lay it out something like pin next to ring with the CG kicked towards the Midline and then have the Opposite MB mark around 3-4 inches away from his PAP.  Anyway,  just wondering if this would be a legal drilling and how it would work, the pros, the cons, etc.  I'm hear to learn so go ahead and teach me.

Thanks,
Jeremy
--------------------
"Strive to be perfect,  that is afterall the only way to become perfect."

"If you compare yourself with others,
you may become vain and bitter;
for always there will be greater and lesser persons than yourself.
Enjoy your achievements as well as your plans."

Taken from Desiderata

Proud user of Columbia 300 and Visionary Bowling Products
Logged

 

J_Mac

  • Hero Member
  • *****
  • Posts: 6778
Re: How do you drill offset asyms
« Reply #1 on: November 11, 2006, 08:02:32 PM »
Sounds like he ended up with a ball like this Rule Delta-1...

http://www.ballreviews.com/Forum/Replies.asp?TopicID=142626&ForumID=14&CategoryID=2
--------------------
"A word to the wise ain't necessary -- it's the stupid ones that need the advice."  Bill Cosby
"Never argue with an idiot. They bring you down to their level and beat you with experience."
Logged

imjouster

  • Hero Member
  • *****
  • Posts: 643
Re: How do you drill offset asyms
« Reply #2 on: November 12, 2006, 10:54:38 PM »
yeah ball is a lot like that Delta 1 as far as layout.  Didn't think about posting this in the track forum but will do.  Hopefully I get some good hits in there.  Thanks

Jeremy
--------------------
"Strive to be perfect,  that is afterall the only way to become perfect."

"If you compare yourself with others,
you may become vain and bitter;
for always there will be greater and lesser persons than yourself.
Enjoy your achievements as well as your plans."

Taken from Desiderata

Proud user of Columbia 300 and Visionary Bowling Products
Logged

Strapper_Squared

  • Hero Member
  • *****
  • Posts: 4231
Re: How do you drill offset asyms
« Reply #3 on: November 13, 2006, 06:18:44 PM »
I would say go ahead and lay it out as you normally would (possibly using a little stronger pin position than normal to help offset the likely required weight hole that's going to be in a flare reducing position).  I would suggest drilling the ring finger extra deep and the thumb as shallow as possible to help out with statics...  Once that's finished, weight it up and drop a weight hole as needed to get the statics back to legal..

S^2
--------------------
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Joe Theismann idiot quote of the week:
"He's a standing statue."
Like there is any other kind of statue?

Logged
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Pages: [1]
« previous next »