Author Topic: First time out with the Gamebreaker and Bash... (Read 1338 times)

jkiser01 · « **on:** July 15, 2007, 08:04:28 AM »

Well I was able to throw each of these balls 3 games today and all I can say is, yes I like them both very much!!..

Gamebreaker-drilled 4 1/2 pin to pap and 3 3/8 cg to pap which placed the pin to the right of the ring finger a smidge with the cg stacked under with a small weight hole on the VAL just below the midline.. All I can say is this brings back great memories of the original V2 solid I once had except this ball is quite a bit stronger.. Probably 5 boards or so. I had no problems using this on a fresh house shot on synthetic lanes standing 25 throwing over 15 out to 5 and it came roaring back no problem. Great pin carry and just a couple of 10 pins for 3 games..

Bash-drilled label leverage with the pin next to the ring and the cg in the palm with no weight. One word describes this ball... smooooooooooooooooth... I was able to stand at about 20 and play straight up the 7-8 board and this ball just crushed the pocket.. I could also swing it some as the lanes broke doen some. The carry was exceptional for a low priced ball. I have been looking for a drier lane ball to roll like this for years and I think I finally found it..

I highly recommend both of these balls and can't wait to use them some more..

I have the Clash coming in this week and the NVS coming on 7/30. I will report my findings on those as well..
--------------------
My first child.. Hannah Allison Kiser born 4/30/2007... My little angel..

Edited on 7/16/2007 9:38 AM

chrisleftwich · « **Reply #1 on:** July 15, 2007, 04:08:37 PM »

good to hear that you like the balls that you just bought.
--------------------
Chris Leftwich
Active Duty Coast Guard member.

jkiser01 · « **Reply #2 on:** July 15, 2007, 04:18:50 PM »

thanks Chris, the problem is I keep buying to many and my wife put a stop to it today!! She thought I still had all the new Hammers I had just bought!! LOL..

I will keep you in mind if me and Tracy ever bowl in any tournamants when he gets back in town. Would like to meet you and bowl a few games together..
--------------------
My first child.. Hannah Allison Kiser born 4/30/2007... My little angel..

mrbowlingnut · « **Reply #3 on:** July 15, 2007, 05:22:52 PM »

I used the gamebreaker today on a fresh medium heavy shot, i was comparing it head up to a slew of new products.

Odyssey pin over ring and mb right below my thumb ball revs up in the mid's and with the mb where it is keeps on hooking. The backend was very nice to create a little tug room, it did not take off on the oil.

T-road solid pin under and cg below no weight hole, ball rolls alot like the gamebreaker the guy bowling with me thought it was the same ball most of the time. I took it to 2k by hand which is the gamebreaker surface, the t-road goes about another 1-2 feet and has same ball motion to it.

Yeah Baby pin over ring and no weight hole, ball keeps on revving and revving very angular ball for an oiler. I could open up the shot with this ball, it would recover were the others would washout.

Element ne10 highly polished in box finish it was great for 10 pin's but otherwise would not even wrinkle more than 3-4 boards.

The gamebreaker shot after shot hit hard and always had the same ball roll to it, on oil i would rank this ball at least a 9 or better.

Author Topic: First time out with the Gamebreaker and Bash... (Read 1338 times)

jkiser01

First time out with the Gamebreaker and Bash...

chrisleftwich

Re: First time out with the Gamebreaker and Bash...

jkiser01

Re: First time out with the Gamebreaker and Bash...

mrbowlingnut

Re: First time out with the Gamebreaker and Bash...