win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Need No mercy Layout help.  (Read 1295 times)

Joebagofdonuts

  • Jr. Member
  • **
  • Posts: 77
Need No mercy Layout help.
« on: December 19, 2006, 07:02:28 AM »
Ok ball is on order an it seems to be a big discussion about the tech/spec, of the layout.  First off I dont know jack about layouts, well some but not enough to keep up with the No mercy discussion.  
Here is my profile:

quote:
league bowling since 2001
avg 170's
tweener avg ball speed
Med. Revs
Axis Rotation:
(30°-59°) Medium side roll with a fairly angular move to the pocket.
Axis Tilt:
(0°-15°) Less than average spin. Ball track near the thumb and fingers


Im going to use a different proshop for this ball, my old proshop switched Mgt.  an Ive seen some of his work "not that good".  What to I need to impress on the proshop about the way I want this ball drilled, (this is the most Ive spent on a ball an would like to screw it up"

Any advice?

thanks
joe
Logged

 

directdrill

  • Hero Member
  • *****
  • Posts: 1588
Re: Need No mercy Layout help.
« Reply #1 on: December 19, 2006, 03:06:05 PM »
Joe,

From what I have read, find a good proshop and make sure that they first watch how you throw the ball and make sure they measure your Positive Axis Point (PAP).  From what I have read, Pin to PAP distances are very important for the No Mercy.  I hope this helps.
--------------------
Hook 'em Horns!
Logged

FastTracker33

  • Hero Member
  • *****
  • Posts: 3472
Re: Need No mercy Layout help.
« Reply #2 on: December 19, 2006, 03:08:20 PM »
Drill it the recommended layout, while putting the PIN 4-5 inches from the PAP, like mentioned above you need to know your PAP. That will help out good. That will give you an agressive reaction also! Hope this helps!!
--------------------
-BrIan
Track Legion

Robo Rule, PoWer MaChine, DEsert HeAt
http://trackbowling.com/  
"Track...you Just can't Beat That!"

Edited on 12/19/2006 4:08 PM
Logged

Joebagofdonuts

  • Jr. Member
  • **
  • Posts: 77
Re: Need No mercy Layout help.
« Reply #3 on: December 19, 2006, 04:04:24 PM »
Thanks everyone I will make sure to bring my ball I use the most so they can see the track, also I will check out the hammer website.
http://www.hammerbowling.com/tech_info/detail.php?drilling=Drilling%20Instructions%208

Edited on 12/19/2006 5:08 PM
Logged

azguy

  • Hero Member
  • *****
  • Posts: 8364
Re: Need No mercy Layout help.
« Reply #4 on: December 19, 2006, 04:29:05 PM »
Do NOT get all hung up on Layout #1, #2 etc, it ALL pin/pap and if the shop does not know that measurement, then you're out of luck. This ball the Heart and pin/pap is the mOST important thing to know. I have drilled several, I don't care what the number is, it's all about reaction desired and pin/pap along with heart placement.

Talk to the driller, make sure he/she has drilled them before and sees you throw, knows what you expect and measures you pap...best advise I can give, Good Luck.
--------------------
az guy aka: R & L Bowlers Pro
rlbowlerspro@cox.net
www.rlbowlerspro.com


Looking for treasures ? Take a look at my wife's ebay store http://www.ebaystores.com/Pitas-Place?refid=store

Logged

Joebagofdonuts

  • Jr. Member
  • **
  • Posts: 77
Re: Need No mercy Layout help.
« Reply #5 on: December 19, 2006, 06:28:18 PM »
thanks azguy,
Logged
Pages: [1]
« previous next »