BallReviews

Equipment Boards => Hammer => Topic started by: dev on January 28, 2006, 04:06:39 AM

Title: I need someone to layout my hawg please.
Post by: dev on January 28, 2006, 04:06:39 AM: http://img.photobucket.com/albums/v472/dev86/Bowling/DSC00055.jpg

Hi guys, this is the current layout of my hawg, I need a layout which is more strong than this. Just went to a new alley where all my balls just won't hook.

thanks guys!
Title: Re: I need someone to layout my hawg please.
Post by: jkiser01 on January 28, 2006, 12:35:54 PM: The pin needs to be above or beside the ring finger to the left with the cg stacked below or to the left some..

Thats a very "safe" and controlled drilling and you are not taking advantage of the balls potential with that drilling..

I would do a full plug and redrill.. Just my opinion..

--------------------
The 2006 Slump is here...

Edited on 1/28/2006 1:24 PM
Title: Re: I need someone to layout my hawg please.
Post by: chitown on January 28, 2006, 03:09:46 PM: Your drill layout looks fairly strong as it is. Your a lefty so it took me a second to think about it. The only thing that could help as far as drilling is concerned would be to move the pin to 3 3/8 from your pap. Other than that I don't see anything else.

Beofre you get the ball plugged and re-drilled I would change the cover. Most of a balls reaction comes from the cover. Dull it down for heavy or polish it for lighter oil.
Title: Re: I need someone to layout my hawg please.
Post by: mrbowlingnut on January 28, 2006, 06:14:47 PM: Take it down to 1000 abralon no polish, if it is too much ball go to 500 abralon and polish with storm reacta shine right on top of that. Ball looks polished compared to my hawg out of the box, probably the only real problem i see myself. The drilling is early roll but for heavier oil that is what you need anyway.
Title: Re: I need someone to layout my hawg please.
Post by: RevLefty on January 28, 2006, 06:32:02 PM: Hey dev that is scary i am a lefty and that is the same drilling i have on my hawg. Problem I had is that i havent found enouh oil for this ball. It burns up at my feet everywhere with this strong of a drilling. This drilling that we both have is an early hooking arc drilling and if there isnt a flood in the heads it is going to burn up at your feet if you have any revs. You put a strong drilling on a very strong ball when i did find a flood in heads this ball is a beast it actually saves energy. I caqn play in oob areas at houses with this . To help you if you want it to save energy sand it to 1500 and then put either a factory polish or a ruf buff polish either way one will save more energy than the other.
--------------------
People are so blue when the gas mask knocks them out. They get sawed to pieces when the blade hits the lane and everyone knows they are Doomed when I set foot in the building!
Title: Re: I need someone to layout my hawg please.
Post by: Cranking_Inferno on January 29, 2006, 02:27:27 AM: drill it 12 o,clock leverage.. stacked... dont be a little girl
Title: Re: I need someone to layout my hawg please.
Post by: dev on January 29, 2006, 06:12:47 AM: quote:
drill it 12 o,clock leverage.. stacked... dont be a little girl

stacked? low ball speed with lov rev rate, not much tilt and rotation, what will this stacked drilling give me ?
Title: Re: I need someone to layout my hawg please.
Post by: dev on January 29, 2006, 06:13:42 AM: Er, for that picture, I polished it after bowling at a house with medium oil. Now I'm bringing it down to 1000 sanded. or maybe 600. Haha.