win a ball from Bowling.com
« previous next »
Pages: 1 [2]

Author Topic: Recommended drilling for a Hot Sauce  (Read 2966 times)

Nicanor

  • Hero Member
  • *****
  • Posts: 2292
Recommended drilling for a Hot Sauce
« on: March 11, 2009, 03:45:08 AM »
Pin above or pin below.  Did not want a skid flip reaction.  My pap is 4 7/8 and 5/8 up about 400 rev rate and approx 17 mph ball speed.

Thanks,

--------------------
Nicanor (Ten On The Deck)
Logged
Nicanor (Ten On The Deck)

 

Nicanor

  • Hero Member
  • *****
  • Posts: 2292
Re: Recommended drilling for a Hot Sauce
« Reply #16 on: March 12, 2009, 10:09:42 AM »
Actually the video on Buddies website is right off (copied)Hammerbowling.com website.

I like the idea of taking a ball that is touted as skid flip and tone it down a little.  I find that some times when I have trouble kicking out a 10 pin, that if I go with a ball that stores a lot of energy and explodes the pocket a little more, then it helps my game to carry the 10 pin.  So if I can drill the skid flippiness out of the ball so its not a hockey stick and more controllable but still pretty angular with good energy retention, then I have a great ball when some of my other equipment is too much of an arc and not driving the pocket.  I also like a ball like that to open up the lanes.  So yes, maybe I'm drilling some of the intended power out of the ball, but if can can harness power and make it more controllable, we might not get too much over under.


--------------------
Nicanor (Ten On The Deck)

Edited on 3/12/2009 10:11 AM

Edited on 3/12/2009 10:11 AM
Logged
Nicanor (Ten On The Deck)

BubbaRay

  • Full Member
  • ***
  • Posts: 118
Re: Recommended drilling for a Hot Sauce
« Reply #17 on: March 12, 2009, 11:20:51 AM »
If you want some expert advice on drillings for The Hot Sauce for what you want it to do, go right to the source.  Send Mr. Ussery an email and explain to him in detail on what you want the Hot Sauce to do.  jussery@hammerbowling.com  
He will give the advice and probably recdommend something for you in layouts.

Mine is a 4X3 layout with a 2 inch pin buffer Pin under drill and this thing is still strong on the back.


--------------------
Nothing Hit's Like A Hammer
Hammer Team Member
   Hammer Message Board Moderator
   PBA Eastern Region Senior Player
   
www.hammerbowling.com
[/b]

Edited on 3/12/2009 11:21 AM
Logged
Jim Sabatell
DV8 Regional Staff
Disclaimer !!  The opinions expressed are solely those of the writer .

Gazoo

  • Hero Member
  • *****
  • Posts: 1872
Re: Recommended drilling for a Hot Sauce
« Reply #18 on: March 12, 2009, 07:06:38 PM »
Quote
So is the Hot Sauce only really at its best as a skid flip?  The ones I've seen locally didn't seem to be skid flippy.  Is that release or ball drilling/prep?  I have enough oil balls, Dynamo, Virtual Gravity, Cell, Agent Orange.  I want a ball to get through the heads easier, have some pop in the back end, but not a hockey stick move.
--------------------

If that is the reaction you want then the Acid is the ball you seek.

--------------------
"I don't want to be remembered, I want to be forgotten"
Logged
Pages: 1 [2]
« previous next »