win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Dynamo X  (Read 3314 times)

Stan

  • Hero Member
  • *****
  • Posts: 667
Dynamo X
« on: September 22, 2009, 07:58:23 AM »
Drilled one out with a 4 1/4 pin to pap and 3 3/8 cg to pap.  This put the pin just over my ring finger and the cg slightly kicked out with no weight hole required.  Tried it out of box and the ball went dead straight.  My Virtual energy and my virtual gravity were hooking but this ball was not.  Took it back to the shop and changed the surface to 2000 abralon, no polish.  The ball did the same thing.  Will probably try taking it down to 500 abralon.

Very confusing, since my Virtual gravity hooked and my virtual energy hooked why this ball did not.  My trak is low, but the track circumferene is around 12 inches.  I also had the same problem with a Brunswick Seige.

Any suggestions ?

Edited on 9/22/2009 3:59 PM
Logged

 

OddBalls

  • Hero Member
  • *****
  • Posts: 3119
Re: Dynamo X
« Reply #1 on: September 22, 2009, 04:05:27 PM »
check your static weights too much thumb weight will cause the ball to go straight and not hook at all.

You should have 132/135 side weight as well..
--------------------
Yes. it's I, the Inverted One..

Logged

OddBalls

  • Hero Member
  • *****
  • Posts: 3119
Re: Dynamo X
« Reply #2 on: September 22, 2009, 04:06:04 PM »
of course I'm kidding..
--------------------
Yes. it's I, the Inverted One..

Logged

Roy Munson

  • Hero Member
  • *****
  • Posts: 1036
Re: Dynamo X
« Reply #3 on: September 22, 2009, 04:15:19 PM »
Isn't that getting a little old
--------------------

Roy Munson: "Morning! I hope you don't mind, I got up a little early. So I took the liberty of milking your cow for you. Yeah, it took a little while to get her warmed up. She sure is a stubborn one. Then pow, all at once."
Mr. Boorg: "We don't have a cow. We have a bull."


***** Looking for Pearl Cherry C/2 *****
***** Looking for Pearl Cherry Bomb *****
Logged

OddBalls

  • Hero Member
  • *****
  • Posts: 3119
Re: Dynamo X
« Reply #4 on: September 22, 2009, 04:19:47 PM »
quote:
Isn't that getting a little old
--------------------

Roy Munson: "Morning! I hope you don't mind, I got up a little early. So I took the liberty of milking your cow for you. Yeah, it took a little while to get her warmed up. She sure is a stubborn one. Then pow, all at once."
Mr. Boorg: "We don't have a cow. We have a bull."


***** Looking for Pearl Cherry C/2 *****
***** Looking for Pearl Cherry Bomb *****


Yes,but that's the answers he'll end up getting from Lane#1..

So maybe I wasn't entirely kidding..
--------------------
Yes. it's I, the Inverted One..

Logged

tizzle

  • Hero Member
  • *****
  • Posts: 2159
Re: Dynamo X
« Reply #5 on: September 23, 2009, 08:08:46 AM »
My original dynamo performed the exact same way. I ended up slowing my ball speed way down, and having a flare hole added. This brought out the reaction some, but nothing extravagant. I ended up selling it!
--------------------
Hmm..Lets see what I have in this bag...some virtual gravity, some hot sauce, a liberator, and a saw.. how can I loose....

....HG-300(2006 w/Desert Heat)...299 (03/15/09 w/Agent Orange)...HS-776 (Hot Sauce Pearl & Ebonite Magic)
Logged

JustABowler

  • Jr. Member
  • **
  • Posts: 33
Re: Dynamo X
« Reply #6 on: September 23, 2009, 09:29:42 AM »
How much flare are you getting? Should be between 4 and 5 inches.
--------------------
Jamie Steelman
Bryan's Bowling Center Pro Shop
Laurel, DE
jamiesteelman@aol.com
Former owner of Sudden Impact Pro Shop
Seaford, DE
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24526
Re: Dynamo X
« Reply #7 on: September 23, 2009, 10:44:29 AM »
Since you're a part time pro shop operator, I would guess that you did this, but one should never assume: did you verify that the CG marking was the actual CG?
--------------------
"None are so blind as those who will not see."
Logged
"None are so blind as those who will not see."

Sir Bowl-A-Lot

  • Hero Member
  • *****
  • Posts: 2981
Re: Dynamo X
« Reply #8 on: September 23, 2009, 10:57:39 AM »
I thought "CG no madduh"...  
Logged

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Re: Dynamo X
« Reply #9 on: September 23, 2009, 11:30:47 AM »
If you have the ball drilled 4-1/4 x 3-3/8 without a weighthole there must have been like no top weight in the ball to start. A layout as such almost always requires a weighthole, especially on Lane 1 balls.

I have my X-2 laid out similar to yours and I cannot even throw it on my home house shot....the ball is too much in the midlane and the backend is way too much.

The ball does work good on a local house with fairly new synthetics though...
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Lane 1 Buzzsaw...The Official Power Tool Of Bowling
For Real Time Interactive Bowling Conversation:
BowlingChat.net
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

OddBalls

  • Hero Member
  • *****
  • Posts: 3119
Re: Dynamo X
« Reply #10 on: September 24, 2009, 12:16:19 PM »
quote:
If you have the ball drilled 4-1/4 x 3-3/8 without a weighthole there must have been like no top weight in the ball to start. A layout as such almost always requires a weighthole, especially on Lane 1 balls.

I have my X-2 laid out similar to yours and I cannot even throw it on my home house shot....the ball is too much in the midlane and the backend is way too much.

The ball does work good on a local house with fairly new synthetics though...
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Lane 1 Buzzsaw...The Official Power Tool Of Bowling
For Real Time Interactive Bowling Conversation:
BowlingChat.net


So, you're saying his static weights are off and that's the reason the ball doesn't hook?
--------------------
Yes. it's I, the Inverted One..

Logged

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Re: Dynamo X
« Reply #11 on: September 24, 2009, 10:56:13 PM »
Go away troll...we don't need your kind around here.
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Lane 1 Buzzsaw...The Official Power Tool Of Bowling
For Real Time Interactive Bowling Conversation:
BowlingChat.net
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

Doug Sterner

  • Hero Member
  • *****
  • Posts: 4395
Re: Dynamo X
« Reply #12 on: September 25, 2009, 09:58:26 AM »
Again I restate my last post....

Go away troll...we don't need your kind around here.
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Lane 1 Buzzsaw...The Official Power Tool Of Bowling
For Real Time Interactive Bowling Conversation:
BowlingChat.net
Logged
Doug Sterner
Doug's Pro Shop
Owego, NY

Proud Member of the NRA
Fighting to uphold the Constitution of the U.S.

Tateman

  • Full Member
  • ***
  • Posts: 163
Re: Dynamo X
« Reply #13 on: September 25, 2009, 02:31:36 PM »
Anyway to post a video?  I am curious to see how it rolls compared to your other stuff.

I don't have any other suggestions though.  To me, a ball should be able to hook just fine in OOB condition.
Logged
Pages: [1]
« previous next »