win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Enriched Uranium coverstock  (Read 953 times)

KMUMPS

  • Jr. Member
  • **
  • Posts: 60
Enriched Uranium coverstock
« on: July 15, 2009, 09:45:28 PM »
A friend just gave me an Enriched Uranium.  I am wondering if anyone could tell me what was the out of box surface for this ball?
Logged

 

OddBalls

  • Hero Member
  • *****
  • Posts: 3119
Re: Enriched Uranium coverstock
« Reply #1 on: July 16, 2009, 01:14:40 PM »
I believe it's the standard 400 grit wet sand w/high gloss finish..
--------------------
Inverted 1 and Dead Flush are my Evil Twins...
Logged

KMUMPS

  • Jr. Member
  • **
  • Posts: 60
Re: Enriched Uranium coverstock
« Reply #2 on: July 16, 2009, 03:55:12 PM »
Thanks a lot OddBalls!
Logged

Steven

  • Hero Member
  • *****
  • Posts: 7680
Re: Enriched Uranium coverstock
« Reply #3 on: July 16, 2009, 04:13:40 PM »
I found mine to have too much over/under OOB with the high gloss finish. When it was time to refresh the cover, I took it to 600 grit with a Green scotchbrite pad and then hit it with 3M Rubbing Compound. It's made the ball more usable across a wider range of medium conditions.

The cover is very adjustable depending on what you're trying to accomplish.
--------------------
As posted by CRD..."You mean Steven is not the king of impartiality? When did that change?"
Logged

Buzzhead

  • Hero Member
  • *****
  • Posts: 2002
Re: Enriched Uranium coverstock
« Reply #4 on: July 16, 2009, 04:39:02 PM »
This was a Brunswick cover, and it is particle. Therefore it is some form of Trizact..... I would have to say 35 or 10 Micron with the standard brunswick polish after it.....

I have mine, one at 2000 Abralon and the other factory.
--------------------
FAILURE IS FEEDBACK. AND FEEDBACK IS THE BREAKFAST OF CHAMPIONS THAT GOT DIGESTED!

Ten pin?????? Where?? I throw a BUZZSAW there is NUTTIN left on the deck...

Proud MEMBER of the FOS!!
Member of the FOS, if there happens to be a 9 pin standing just toss a saw and cut it down~~!
Logged
FAILURE IS FEEDBACK. AND FEEDBACK IS THE BREAKFAST OF CHAMPIONS THAT GOT DIGESTED!

Ten pin?????? Where?? I throw a BUZZSAW there is NUTTIN left on the deck...

Proud MEMBER of the FOS!!
Member of the FOS, if there happens to be a 9 pin standing just toss a saw and cut it down~~!

Steven

  • Hero Member
  • *****
  • Posts: 7680
Re: Enriched Uranium coverstock
« Reply #5 on: July 16, 2009, 05:01:38 PM »
quote:
This was a Brunswick cover, and it is particle. Therefore it is some form of Trizact..... I would have to say 35 or 10 Micron with the standard brunswick polish after it.....


Yes it's particle, but very low load. It's nothing like the older SCB cover, which certainly was finished with 35 Micron Trizact. I'm not sure Trizact is a real requirement for the Enriched.
--------------------
As posted by CRD..."You mean Steven is not the king of impartiality? When did that change?"
Logged

KMUMPS

  • Jr. Member
  • **
  • Posts: 60
Re: Enriched Uranium coverstock
« Reply #6 on: July 17, 2009, 05:59:08 AM »
Thanks everyone!  I will play around with it and see what it does.  I was just looking for a base to start from.
Logged
Pages: [1]
« previous next »