BallReviews
Equipment Boards => Lane #1 => Topic started by: L o G on February 08, 2006, 01:41:22 PM
-
Hello all,
Tonight I got bored and decided to take my Uranium to 2000 grit but don't bowl till next Tuesday (like I said I was bored). I also did it to give it a better cleaning. Cleaned it then sanded it then cleaned it again. Now I am wondering what kinda reaction I will get out of it at 2000. I am thinkin that when I am in the proshop next week of getting it polished again cause I like it that way but I also wanna try it dull and my proshop is in a different house than where I bowl.
--------------------
What I really meant to say
Is I'm sorry for the way I am
I never meant to be so cold
never meant to be so cold
-
I don't know for you but I know that I was throwing my Solid sanded with a red scotch bright and it worked ok, but when I polished it up it hooked a lot more and it was more controllable. I would also recommend that you try to get yourself a ball spinner if you like to take control of your ball and experiment.
--------------------
John Bostic
-
No it did'nt scratch it. I have one of those 2000 grit pads so there were no lines on it. The 1000 pad I have does end up leaving lines on it if I don't use a spinner but the 2000 even without a spinner just leaves the ball dull.
--------------------
What I really meant to say
Is I'm sorry for the way I am
I never meant to be so cold
never meant to be so cold
-
quote:
No it did'nt scratch it. I have one of those 2000 grit pads so there were no lines on it. The 1000 pad I have does end up leaving lines on it if I don't use a spinner but the 2000 even without a spinner just leaves the ball dull.
--------------------
What I really meant to say
Is I'm sorry for the way I am
I never meant to be so cold
never meant to be so cold
There are 2 Uraniums: solid and pearl. Which one are you talking about?
shuturhole316tx said he was talking about the solid.
Sue,
"red" (usually called maroon; it's a dark red) Scotch-Brite is the roughest one; it is approximately 320 grit. That is VERY rough finish for a solid ball like the Uranium,
shuturhole316tx,
The reason the polished one hooked more is probably becasue the roughly sanded one was too rough for the oil you faced and your ball speed. It was probably expending all its energy in the midlane and had nothing left for the backend. The polish allowed it to be cleaner, save energy and hook more and hit harder by the time it got to the pins.
--------------------
"...for advice is a dangerous gift, even from the wise to the wise...."
J. R. R. Tolkien
-
Urban legend: rough surface on the ball will make it hook more!
In actuality, the reverse is true. Rough surface has less surface contact with the lane which cause less friction, which cause less hook.
I'm pretty sure many will discredit this!
--------------------
I Saw You !
-Noel
-
quote:
Urban legend: rough surface on the ball will make it hook more!
In actuality, the reverse is true. Rough surface has less surface contact with the lane which cause less friction, which cause less hook.
I'm pretty sure many will discredit this!
You don't really believe this do you??
--------------------
Don't argue with an idiot; people watching may not be able to tell the difference.
-
My take on ball surface has always been:
Shinny balls go longer before they start to hook.
Dull balls start to hook sooner.... Notice I didn't say hook more.
FOS
Joe
-
Exactly. Hooks sooner, loses a lot of energy going through the front and midlane, dies on the backend.
--------------------
I Saw You !
-Noel
-
quote:
Exactly. Hooks sooner, loses a lot of energy going through the front and midlane, dies on the backend.
--------------------
I Saw You !
-Noel
It all depends on the relationship between the amouint of oil, the ball's coverstock strength, the ball's surface finish, and the bowler's speed.
If you have enough oil, then rougher coverstocks will make the ball hook more. Not an urban legendd; it's called physics!
--------------------
"...for advice is a dangerous gift, even from the wise to the wise...."
J. R. R. Tolkien
-
We're talking about one type of ball - Uranium
two different surface;
one is roughly sanded,
the other, finely sanded
the same set of lanes.
The question is which one loses more energy due to friction from front and midlane ?
--------------------
I Saw You !
-Noel
-
I have the pearl Uranium. I am probly gonna get it polished back up but am gonna throw it dull first. Y'all have a good one.
--------------------
What I really meant to say
Is I'm sorry for the way I am
I never meant to be so cold
never meant to be so cold
-
quote:
We're talking about one type of ball - Uranium
two different surface;
one is roughly sanded,
the other, finely sanded
the same set of lanes.
The question is which one loses more energy due to friction from front and midlane ?
Depends on oil pattern. If there's enough oil your finely sanded ball will skid 60 feet, a lot of good all that storing of energy will do. The roughly sanded ball will grab, hold and still have some kick left for the backend. OVERALL hook, not just backend hook, is what is meant by a total hook rating on rough (dull) surfaced balls. On an oily pattern your slick surface will never have enough traction to use this energy that you're worried about losing in the heads and mid-lane.
--------------------
Don't argue with an idiot; people watching may not be able to tell the difference.