win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: 3M Finesse-It II?  (Read 5792 times)

lrtrees

  • Jr. Member
  • **
  • Posts: 73
3M Finesse-It II?
« on: August 20, 2009, 02:00:17 AM »
I seem to recall reading a number of times that car/boat products are not good to use on a bowling ball and am wondering if that theory has changed or is it just a few select products that we are considering?

I see several here mentioning that they are using this, 3M Finesse-It II and I am am wondering if that is a good thing?  And if so, what does it compare to?

Thanks, I am still learning.
Lon
Logged

 

pin-chaser

  • Hero Member
  • *****
  • Posts: 1802
Re: 3M Finesse-It II?
« Reply #1 on: August 20, 2009, 03:13:45 PM »
Ive used this for several years on several bowlers balls.
Logged
Sponsored by: http://bowlerx.com



Chasing pins for 45 years.

Cobalt Bomb

  • Hero Member
  • *****
  • Posts: 2053
Re: 3M Finesse-It II?
« Reply #2 on: August 20, 2009, 03:19:25 PM »
It was used by Columbia for several years by name, and is probably the basis of many of the current polishes on the bowling market.
Logged

lrtrees

  • Jr. Member
  • **
  • Posts: 73
Re: 3M Finesse-It II?
« Reply #3 on: August 20, 2009, 03:43:10 PM »
Do we know approx the grit or finish it will apply to the ball?
Logged

dizzyfugu

  • Hero Member
  • *****
  • Posts: 7606
Re: 3M Finesse-It II?
« Reply #4 on: August 21, 2009, 03:42:29 AM »
The stuff is great! It is a fine rubbing compound, intended to smooth out surfaces in the 2.000-4.000 grit scale. The result is a very even, shiny finish - looks like polished, but just the pure coverstock, no wax or the like.
The finish offers very good length through the heads and IMO a better control at the break point than many polishes. And a reactive surface becomes very tacky, so that pin mix upon impact is very good.
--------------------
DizzyFugu - Reporting from Germany

Confused by bowling? Check out BR.com's vault of wisdom: the unofficial FAQ section
Logged
DizzyFugu ~ Reporting from Germany

Cobalt Bomb

  • Hero Member
  • *****
  • Posts: 2053
Re: 3M Finesse-It II?
« Reply #5 on: August 21, 2009, 04:23:52 AM »
quote:
Do we know approx the grit or finish it will apply to the ball?


The bottle says it will remove 1500 grit (sandpaper)or finer scratches. I find this compares well to Ebonite Factory Finish.

There is more info on the 3M website, but I haven't been there in a while.
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24526
Re: 3M Finesse-It II?
« Reply #6 on: August 30, 2009, 06:27:37 PM »
quote:
I seem to recall reading a number of times that car/boat products are not good to use on a bowling ball and am wondering if that theory has changed or is it just a few select products that we are considering?


There never has been any "theory" about applying car or boat products to bowling balls. It has always depended on the individual product. Basically, you always wanted a product that does not contain silicone/silicon which plugs the pores of resin compounds. Since Brunswick first produced resins, they have recommended auto rubbing and polishing compounds to polish their balls UNTIL they produced/purchased the right to market their own products.

quote:

I see several here mentioning that they are using this, 3M Finesse-It II and I am am wondering if that is a good thing?  And if so, what does it compare to?
Lon


As Dizzy says above, Finesse-it is a light abrasive polishing compound that puts a nice wet look gloss on most balls. There is no specific grit rating that I am aware of. As with most, more depends on the grit level to which you sand the ball before applying the polish. I'd also agree with Dizzy that the level will often wind up in the 2000 grit FEPA(Abralon)/1000 grit US or higher range.

--------------------
"None are so blind as those who will not see."
Logged
"None are so blind as those who will not see."
Pages: [1]
« previous next »