win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: bringing a ball back to life  (Read 2398 times)

machine35

  • Jr. Member
  • **
  • Posts: 57
bringing a ball back to life
« on: November 21, 2011, 12:11:23 PM »
i have not used my black widow bite for over a mth. the last couple of weeks i have started to use it again. what can i do to bring it back to form after a short hiatus?


Logged

 

tommyboy74

  • Hero Member
  • *****
  • Posts: 1831
Re: bringing a ball back to life
« Reply #1 on: November 21, 2011, 08:49:28 PM »

I would use a good deep cleaner such as Powerhouse Clean n' Dull which will definitely get rid of some of the dirt and oil.  Probably wouldn't hurt to redo the surface either on a spinner or by hand. 



My arsenal

Heavy Oil: Storm Virtual Gravity Nano: 2000 AB
Medium-Heavy Oil: Storm Anarchy: 1500 polished
Medium-Heavy Oil: Ebonite Vital Energy: 4000 AB
Medium Oil: Roto Grip Nomad Dagger: 1500 polished

Medium-Light Oil: Roto Grip Rising Star: 1500 polished
Logged
Current Ball Arsenal
Heavy:
MOTIV Jackal Legacy
MOTIV Mythic Jackal

Med-Heavy:
MOTIV Trident Odyssey
MOTIV Forge Fire
MOTIV Covert Revolt

Medium:
MOTIV VIP ExJ Sigma
MOTIV Sigma Sting
MOTIV Pride Solid

Medium-Light
MOTIV Venom Shock
MOTIV Tribal Fire

completebowler

  • Hero Member
  • *****
  • Posts: 5491
Re: bringing a ball back to life
« Reply #2 on: November 21, 2011, 11:31:39 PM »
Run some tap water as hot as it comes out into a 5 gallon bucket and mix in some Dawn dish soap. Let the ball sit for around 10 minutes. Dump it out and refreshen. Depending on how many games are on a ball I will do this 2-3 times.

 

Then take it to the spinner and sand 4 sides at 360. Four sides at 500. Then go directly to the factory finish grit. Which I think was 2000 on the Bite.

 

 


ALL STAR BOWLING & TROPHY
LANGAN'S ALL STAR LANES
IBPSIA MEMBER
WALLED LAKE MI
Logged

Steven

  • Hero Member
  • *****
  • Posts: 7680
Re: bringing a ball back to life
« Reply #3 on: November 22, 2011, 08:26:27 AM »
+1 to complete. Excellent method for restoring a ball.
 



completebowler wrote on 11/22/2011 0:31 AM:
Run some tap water as hot as it comes out into a 5 gallon bucket and mix in some Dawn dish soap. Let the ball sit for around 10 minutes. Dump it out and refreshen. Depending on how many games are on a ball I will do this 2-3 times.


 


Then take it to the spinner and sand 4 sides at 360. Four sides at 500. Then go directly to the factory finish grit. Which I think was 2000 on the Bite.


 


 



ALL STAR BOWLING & TROPHY
LANGAN'S ALL STAR LANES
IBPSIA MEMBER
WALLED LAKE MI


Logged

charlest

  • Hero Member
  • *****
  • Posts: 24524
Re: bringing a ball back to life
« Reply #4 on: November 22, 2011, 08:33:22 AM »
Corrected!!
 
completebowler wrote on 11/22/2011 0:31 AM:
Run some tap water as hot as it comes out into a 5 gallon bucket (Make sure you can put your hand in it without burning yourself, as some people keep their water heaters above the 140 degree mark that is around the safe maximum temperature for bowling balls.) and mix in some Dawn dish soap. Let the ball sit for around 10 minutes. Dump it out and refreshen. Depending on how many games are on a ball I will do this 2-3 times.

 

Then take it to the spinner and sand 4 sides at 360. Four sides at 500. Then go directly to the factory finish grit. Which I think was 2000 on the Bite.

 

 


ALL STAR BOWLING & TROPHY
LANGAN'S ALL STAR LANES
IBPSIA MEMBER
WALLED LAKE MI


"None are so blind as those who will not see."

 
Logged
"None are so blind as those who will not see."

ImBackInTheGame

  • Hero Member
  • *****
  • Posts: 1022
Re: bringing a ball back to life
« Reply #5 on: November 22, 2011, 11:51:17 AM »
If you do have a spinner, sand it to 360 first then give it a hot water bath.  Need to open up those pores.
Logged

milorafferty

  • Hero Member
  • *****
  • Posts: 11166
  • I have a name, therefore no preferred pronouns.
Re: bringing a ball back to life
« Reply #6 on: November 22, 2011, 12:10:12 PM »
I've read this quite a few times, but just have not found it to be necessary. I will sand down to 360 if I intend to do a resurface afterwards, but not just to do an oil extraction. It seems to me that the oil got into the ball just fine with out the pores being open, so it should be able to get back out. But I could be wrong! 
 
I use a portable dishwasher and get great results.
 
ImBackInTheGame wrote on 11/22/2011 12:51 PM:If you do have a spinner, sand it to 360 first then give it a hot water bath.  Need to open up those pores.
Logged
"If guns kill people, do pencils misspell words?"

"If you don't stand for our flag, then don't expect me to give a damn about your feelings."

ImBackInTheGame

  • Hero Member
  • *****
  • Posts: 1022
Re: bringing a ball back to life
« Reply #7 on: November 22, 2011, 12:57:22 PM »
Yes, it still works fine it just takes longer to get all of the oil out if you don't sand it first.  I've done it both ways.
 
milorafferty wrote on 11/22/2011 1:10 PM:
I've read this quite a few times, but just have not found it to be necessary. I will sand down to 360 if I intend to do a resurface afterwards, but not just to do an oil extraction. It seems to me that the oil got into the ball just fine with out the pores being open, so it should be able to get back out. But I could be wrong! 
 
I use a portable dishwasher and get great results.
 
ImBackInTheGame wrote on 11/22/2011 12:51 PM:If you do have a spinner, sand it to 360 first then give it a hot water bath.  Need to open up those pores.


Logged
Pages: [1]
« previous next »