Author Topic: How picky are you with ball specs? (Read 1743 times)

bamaster · « **on:** December 29, 2004, 06:00:31 AM »

I had to cancel a ball I sold the other day because I was unable to locate the exact specs that the customer wanted. The problem was that it wsa a discontinued ball so finding it was more difficult than usual. The manufacturer didn't even have it in their warehouse.

So my question is... how adamant are you with your ball weight, top weight, pin distance requirements?

Me? I'm not at all. I don't bowl with asymmetrical cores so the MB is insignificant. My ball driller, Mike Austin, can make it do what I want it to do.

What about you?

Tony
Like chips and salsa, http://www.allBowling.com is good!

Edited on 12/29/2004 3:00 PM

Doug Sterner · « **Reply #1 on:** December 29, 2004, 02:13:29 PM »

I am more fussy with symmetrical core balls than the assymetrical ones. The core strength on those balls is such that I can drill just about anything to do what I want it to do. Generally I request 2-4" and 2-3.5 oz for specs.

Examples:

Predator Pursuit with a 5-1/2" pin...put pin above the bridge and cg right of the thumb, hit the box finish with some CLean N Sheen and it's a gem on the house pattern

Trauma ER with pin BETWEEN the CG and MC2...the Determinator sais the MC2 was right and the balance said the cg was right. not sure how it rnded up as such but it did...put the pin below the ring and the cg in the bridge and it all worked out fine.

No problems :-)
--------------------
Doug Sterner
Doug's Pro Shop
Owego, NY
http://dougsproshop@aol.com
www.dougsproshop.net
Hide the women and children...
The Dirty Bomb cometh!!!
Now accepting VISA/MC and Discover for your purchases

DanH78 · « **Reply #2 on:** December 29, 2004, 02:20:29 PM »

As long as it's close, then I'm fine. I ordered an Erase It and I wanted a 1-2 inch pin with 3-3.5 top, it showed up at the pro shop with a 4.5" pin, so I sent it back. But as long as it's ABOUT what I'm looking for, then I trust my driller to get it to do what we want it to do.
--------------------
The clock on the wall says 3 O'Clock...last call...for Alcohol!
"I love a martini -- but two at the most. Three Iâ€™m under the table; Four, Iâ€™m under the host." Dorothy Parker

FBM357 · « **Reply #3 on:** December 29, 2004, 02:23:26 PM »

Usually ask for:
3-5" pin
3.5+ TW

purchased a short pin ball & low TW for the first time and wasn't too bad, but the above works better for me.

stanski · « **Reply #4 on:** December 29, 2004, 02:25:48 PM »

I'm usually picky on pin length, usually ask for 3-4 inch pin, shorter if i plan on using pin under ring. only time i am picky on top weight is when drilling close to the axis, then I ask for under 3 ounces.
--------------------
stanski

sdbowler · « **Reply #5 on:** December 29, 2004, 02:27:23 PM »

For both tw and pin have been on a kick of anywhere from 2-4. Has worked well for me.
--------------------
nothing fancy or catchy to say in my signature

RSalas · « **Reply #6 on:** December 29, 2004, 02:30:04 PM »

It really depends on the reaction that I'm looking to get. I usually stick to the layouts on the drill sheets, which typically call for pins in the 1"-2" range or in the 3"-4" range. However, I can usually find a way to make a 2"-3" pin work for me.

Top weight is largely irrelevant to me, as I seldom if ever use an XH.
--------------------
"Dispensing conventional wisdom to a fingertip world."

Horrid in Doubles, torrid in Singles...
...that's The Curse of Dusty.

clintdaley · « **Reply #7 on:** December 29, 2004, 02:42:40 PM »

2-3 pin, less than 4 ounces of top.
I drill almost everything the same way, pin below ring, cg in the palm, so anything more than 3 inches is tough to work with.

Clint
--------------------
Clint Daley-Owner
Lets Go Bowling Daley
Salem, Ohio 44460
TRACK ADVISORY PRO SHOP STAFF

Brickguy221 · « **Reply #8 on:** December 29, 2004, 07:59:25 PM »

quote:
How picky are you with ball specs?

Very........Second to none.

CharlieBrown · « **Reply #9 on:** December 29, 2004, 08:21:21 PM »

Tony,

Quite picky!

I'm the guy who asked you to find me the X Factor (3" - 3.5" pin, with pin, CG and RAD in line) and the Crisis from London U.K., so you know what I'm like!

--------------------
It is what it is.

Vice President of the I-Hate-Lefties-Club (Founded by Del Ballard Jr.)

bamaster · « **Reply #10 on:** December 29, 2004, 08:49:12 PM »

quote:
Tony,

Quite picky!

I'm the guy who asked you to find me the X Factor (3" - 3.5" pin, with pin, CG and RAD in line) and the Crisis from London U.K., so you know what I'm like!

hehe... yeah I got his Crisis. Still working on the X Factor. In your case I can understand. Shipping overseas is going to be pricey and take a while. You certainly should only do it if you get exactly what you're looking for.

This reminds me, I need to give the distributor a call. I might have to call Storm on this X Factor... Mister Picky!

Tony

CharlieBrown · « **Reply #11 on:** December 29, 2004, 09:10:04 PM »

quote:
This reminds me, I need to give the distributor a call

You mean you still haven't called them??? Mmmmmmmmmmmm I smell negative feedback!!!!!!

--------------------
It is what it is.

Vice President of the I-Hate-Lefties-Club (Founded by Del Ballard Jr.)

David Lee Yskes · « **Reply #12 on:** December 30, 2004, 02:46:54 AM »

Normally for most of my stuff, i want 3-4 inch pin, and atleast 3oz of top weight.

For the heavier hooking stuff, i like to have atleast a 3.5inch pin and 3.5top weight, so i can have several options for drillings. And to make sure the ball gets down the lane far enough.

My Reloaded has a 4.5inch pin lol but the pin,CG,rad is all inline. But i guess it depends on the ball i am ordering too.
--------------------
" Lift Your Skirt Grab Your Balls and Learn How to Bowl "

louie · « **Reply #13 on:** December 30, 2004, 07:06:54 AM »

I like either short pins with low top weight (under 2.5 ounces), or pins 2-4 and around 3 inches of top weight.
--------------------

Why does everyone laugh when I bowl?

louie

Mike Austin · « **Reply #14 on:** December 30, 2004, 01:04:33 PM »

For me, myself, not very picky at all. Like Tony says, You can use almost any pin and get the reaction that you are looking for.

For customers, a "little", more picky. Only because most people get worried when the layout looks odd at all.

The fit and surface is the most important thing. Layout helps a little, the people that are really helped by layout bowl for a living. People put too much emphasis on this stuff. If you make a crappy shot, all the magic layouts in the world can't help you, you still threw the ball crappy. If you make a good shot, it is gonna hit the pocket, even if it's a plain ole Power Groove or Scout Reactive. If you make a great shot, you can strike with a house ball.

I think that is 6 cents worth!!

Have a safe, striking, Happy New Year!!!

--------------------

Mike Austin's Precision Pro Shop
Houston, TX
Drilling and Tech Advice BirdDogbowling.com

Driller to many "Stars" and Tony Melendez too!