win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: thumb mold issue  (Read 1398 times)

xrayjay

  • Hero Member
  • *****
  • Posts: 2686
thumb mold issue
« on: September 14, 2011, 08:15:18 AM »
   I use a mold for my thumb which is shorter than the actually hole. I use my strike ball for spares throwing end-over-end or a back up ball. Well, during practice I managed to release the ball landing on the thumb hole which pushed my thumb insert down to about 1/16" or less.

 

Should I worry about it? I re-positioned the tapes in the thumb a little higher and the feel is not that much different.

 

Thanks in advance for your help.


 Tag Team Coaching Success Story   AKA: addik
Logged
Does a round object have sides? I say yes, pizza has triangles..

aka addik since 2003

 

Gunny

  • Hero Member
  • *****
  • Posts: 1543
  • Zombie Hunter
Re: thumb mold issue
« Reply #1 on: September 14, 2011, 05:06:07 PM »
If it hasn't sunk all the way to the bottom yet, it will.  Best bet is to have a new one put in.  Or if your lucky and can pull the one that's in it out, and re-do it.  but more than likely your gonna have to just have it drilled out, and a new one put in.

------------------------------------------------
A bizarre incident occurred in the outskirts of an American suburb.....It was later revealed that the terrible disaster had been caused by the T-Virus.....a mutagentic toxin created by international enterprise Umbrella Incorporated for use in bio-weapon experiments.
 
Don't worry the zombies are looking for brains, you're safe.....
Logged

icefiction

  • Sr. Member
  • ****
  • Posts: 423
Re: thumb mold issue
« Reply #2 on: September 14, 2011, 07:00:49 PM »
next time pour some plug in the hole if you can see it is too short from the get go, then it cant fall down.



Logged


Whos Left

  • Full Member
  • ***
  • Posts: 105
Re: thumb mold issue
« Reply #3 on: September 14, 2011, 07:26:01 PM »
fIX IT--NEW ONE


Logged

raiderh20boy

  • Hero Member
  • *****
  • Posts: 1735
Re: thumb mold issue
« Reply #4 on: September 14, 2011, 08:05:18 PM »
If you release it again like that, I would assume that you will crack/chip the edge of the hole. If you are in the Bay Area NorCal if you want to come by my shop, I'll pull it out and reset for you!


Use "IT" and BOWL UP A STORM!!
Logged

xrayjay

  • Hero Member
  • *****
  • Posts: 2686
Re: thumb mold issue
« Reply #5 on: September 15, 2011, 08:00:26 AM »
 Thanks guys.. I'll try to reset it tonight after work.. The garage is a mess right now. (I can't even get to the spinner and sink lol)


R2B....where's your shop located? I'll be in Pinole in a couple of weeks bowling... Are you near by? Let me know.

Thanks again guys


 Tag Team Coaching Success Story   AKA: addik
Logged
Does a round object have sides? I say yes, pizza has triangles..

aka addik since 2003

Gunny

  • Hero Member
  • *****
  • Posts: 1543
  • Zombie Hunter
Re: thumb mold issue
« Reply #6 on: September 15, 2011, 08:47:22 AM »
I've done this a few times and it works.  Now I have the drill bit marked to know how deep to make the hole.
 
icefiction wrote on 9/14/2011 7:00 PM:next time pour some plug in the hole if you can see it is too short from the get go, then it cant fall down.





------------------------------------------------
A bizarre incident occurred in the outskirts of an American suburb.....It was later revealed that the terrible disaster had been caused by the T-Virus.....a mutagentic toxin created by international enterprise Umbrella Incorporated for use in bio-weapon experiments.
 
Don't worry the zombies are looking for brains, you're safe.....
Logged
Pages: [1]
« previous next »