win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: What do I do if...?  (Read 1211 times)

guffnuh

  • Sr. Member
  • ****
  • Posts: 419
What do I do if...?
« on: January 17, 2010, 09:18:35 AM »
my urethane (Storm Natural) is over-under?
--------------------
High Game: 300 X3
High Series: 814,806
Average: 215
Spokane JBT Titles: 1
Almost 5 years of bowling
14 years old

What''s the difference between ignorance and apathy?

I don''t know and I don''t care!

youtube.com/guffnuh
WATCH MY BOWLING VIDEOS!!!!!
Logged

 

Joe Jr

  • Hero Member
  • *****
  • Posts: 2776
Re: What do I do if...?
« Reply #1 on: January 17, 2010, 05:26:50 PM »
Urethane over/under? Must not be throwing it on the intended conditions. You can always knock the surface down, but urethane's are not a versatile ball.
--------------------
My Game
Just another hack with too much equipment.
Logged

tc300

  • Hero Member
  • *****
  • Posts: 518
Re: What do I do if...?
« Reply #2 on: January 17, 2010, 05:38:31 PM »
could be layed out wrong too.........
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24524
Re: What do I do if...?
« Reply #3 on: January 17, 2010, 07:27:11 PM »
guffnuh,

I'd suggest a couple of possible "problem" areas.
1. you're using it on too much oil.
2. You have a higher amount of axis tilt than average (20 degrees of more).
3. You're using it improperly on a short, heavy oil, with LOTS and LOT SOf very clean, super dry backends + either too much tilt or too much rotation.

You'd also have had this problem back in the 80s with the short oil most of us were subject to.

If (1), then switch to a dull solid resin, with a low pin.
If (2) or (3), then dull the Natural to a lower grit surface
OR
remove some of the shine you have on it
OR
Move to another house.

--------------------
"None are so blind as those who will not see."
Logged
"None are so blind as those who will not see."

Mike Austin

  • Hero Member
  • *****
  • Posts: 2057
Re: What do I do if...?
« Reply #4 on: January 17, 2010, 09:18:23 PM »
quote:
guffnuh,

I'd suggest a couple of possible "problem" areas.
1. you're using it on too much oil.
2. You have a higher amount of axis tilt than average (20 degrees of more).
3. You're using it improperly on a short, heavy oil, with LOTS and LOT SOf very clean, super dry backends + either too much tilt or too much rotation.

You'd also have had this problem back in the 80s with the short oil most of us were subject to.

If (1), then switch to a dull solid resin, with a low pin.

If (2) or (3), then dull the Natural to a lower grit surface
OR
remove some of the shine you have on it
OR
Move to another house.

--------------------
"None are so blind as those who will not see."


What about shine the ever lovin' pi.... out of it, so that it doesn't hook much at all?
--------------------
Check out my blog:

www.strikes4days.blogspot.com

Logged
Mike Austin's Bowling Dynamix Pro Shops
Inside Emerald Bowl
Inside Tomball Bowl
Track Pro Staff Member
Vise Grips Staff Member

MillWorker

  • Jr. Member
  • **
  • Posts: 86
Re: What do I do if...?
« Reply #5 on: January 17, 2010, 10:59:38 PM »
Throw it better
Logged
Pages: [1]
« previous next »