BallReviews

Equipment Boards => MoRich => Topic started by: jkiser01 on December 11, 2005, 11:10:42 PM

Title: Seek and Destroy drilling question..
Post by: jkiser01 on December 11, 2005, 11:10:42 PM

Does anyone have one of these drilled up yet with a pin above or pin beside the ring finger drilling? I am getting one punched up later on today and was curious which one of these drills would work the best.. I am looking for a big backend move for this ball..

I am a very high tracker so I can do funky pin placement drillings..

Any help would be appreciated..
--------------------


jkiser01

Edited on 12/12/2005 12:30 PM

Title: Re: Seek and Destroy drilling question..
Post by: jkiser01 on December 12, 2005, 11:23:31 AM

anyone??????
--------------------


jkiser01

Title: Re: Seek and Destroy drilling question..
Post by: jkiser01 on December 12, 2005, 11:40:30 AM

yea, I know what the drill sheet says, just looking for someone that drilled one with the pin above the ring. The drill sheet does not show any drilling like that. They are all pin beside or pin under..
--------------------


jkiser01

Title: Re: Seek and Destroy drilling question..
Post by: Jeffrevs on December 12, 2005, 04:26:38 PM

a driller who is familiar w/ Mo's stuff should be able to take care of you Jim.

Shouldn't matter w/ a strong mass bias ball!  I'm a high tracker too, and I can have a pin on one of Mo's balls below my ring finger no problem

The real issue is how the ball is laid out according to YOUR specifications.

Pin higher or lower will matter based upon that....remember, 3 3/8 is 3 3/8s, but it's distance above the midline will determime some lenght, the placement of the mass bias will give it it's shape.

strapper...that's hardly sharp break point...yes ? sharp break is always very close to 3 3/8 pin to pap w/ Mo's stuff.....4.5 is very different.....in strong asyms...AND...don't forget,....1/4 to a 1/2 inch in mb placement can make a big difference.....target holes make the difference too.

Jim, message King of the mill w/ your specs
--------------------
JEFF
"...Sorry, I'm just,...it's starting to hit me like a, uhm....uhm...2 ton....heavy thing.."

Title: Re: Seek and Destroy drilling question..
Post by: jjweb on December 12, 2005, 10:48:04 PM

Sorry to hijack the post...

I should be getting a S&D soon, and I have a question about pin height also. I contacted MoRich on how to drill it, and they suggested to go: 3 3/8" X 5 1/4" MB - 2 1/8" pin above midline.

Looking at the high track layout, 3 3/8" X 6" - 3" pin above midline.

Could the lower pin height (2 1/8" versus 3") cause the ball to burn too much energy, because of my slower ball speed?

Title: Re: Seek and Destroy drilling question..
Post by: tekneek on December 13, 2005, 08:02:43 AM

I have one drilled 3-3/8 x 5-1/2 x 3-1/4  this places the pin above(1") and just left of the ring, I seem to have a couple feet more length opposed to the pin being at 2" or less. I have a much more angular movement rather the smooth arcing motion of the ball being drilled pin under ring.
--------------------
Steve
Stars and Strikes Pro Shop

Title: Re: Seek and Destroy drilling question..
Post by: tekneek on December 13, 2005, 10:45:41 AM

jk, check your pm's
--------------------
Steve
Stars and Strikes Pro Shop

Title: Re: Seek and Destroy drilling question..
Post by: jkiser01 on December 13, 2005, 10:58:32 AM

I got your message.. thanks... If I get some free time today at work, I will give you a call..
--------------------


jkiser01