win a ball from Bowling.com
« previous next »
Pages: 1 2 [3]

Author Topic: Target weighting  (Read 5343 times)

snowman4951

  • Hero Member
  • *****
  • Posts: 771
Target weighting
« on: March 14, 2005, 04:38:03 PM »
I was talking to someone about the Shock and Awe. They said you need to have it drilled "Target Weighting" technique.What is this?Is this drilling technique just for Morich balls?Thanks!
--------------------
FIRE ON THE LANES,ICE IN THE VEINS!!!!
Logged

 

Traumatize

  • Hero Member
  • *****
  • Posts: 810
Re: Target weighting
« Reply #31 on: March 22, 2005, 12:13:43 AM »
How do you know what the correct hole-size to use is...Is there also a chart for that?
--------------------
*Erie Community College bowling*

Buffalo bowlers are the best all around in the country.
Logged

Traumatize

  • Hero Member
  • *****
  • Posts: 810
Re: Target weighting
« Reply #32 on: March 22, 2005, 04:02:24 PM »
I just drilled a Ravage today.  Pin 2.5 inches from PAP, 1.75 inches above the midline.  MB is 6.5 inches from PAP, left of midplane (thumb).  The ball has a short pin, so it ended up with 2 ounces of side weight, and 2.75 ounces of top weight.  My question is, where should I put the weight hole?  I have been trying to figure out the target weighting system, but to no avail.  I want the hole to be flare decreasing, so I should put it inside my VAL correct?  My other question is once i've found a spot for the weight hole, how big of a hoel and how deep should I go?  Incase you are wondering, there is no finger or thumb weight, as I drilled the fingers deeper.  I also drilled the ring finger a half inch deeper than the middle to cut some side weight out.  Any information would be greatly appreciated.
--------------------
*Erie Community College bowling*

Buffalo bowlers are the best all around in the country.
Logged

Traumatize

  • Hero Member
  • *****
  • Posts: 810
Re: Target weighting
« Reply #33 on: March 22, 2005, 05:18:58 PM »
Thanx Doc.  But what will my ending weights be?
--------------------
*Erie Community College bowling*

Buffalo bowlers are the best all around in the country.

Edited on 3/22/2005 6:13 PM
Logged

Traumatize

  • Hero Member
  • *****
  • Posts: 810
Re: Target weighting
« Reply #34 on: March 22, 2005, 05:23:38 PM »
So how deep should I go to start with exactly 1 ounce?  Or should I start the hole and re-weigh to see where i'm at, and go from there?
--------------------
*Erie Community College bowling*

Buffalo bowlers are the best all around in the country.
Logged

T-GOD

  • Hero Member
  • *****
  • Posts: 2141
Re: Target weighting
« Reply #35 on: March 23, 2005, 01:20:01 PM »
If you want to target weights perfectly, all you need is Lane #1's Gravity Balance System. This has been around for a long time.

Yes, ending weights do matter..!! By changing the ending weights, you will change the ball reaction/spin time, PSA, ect... =:^D
Logged

jimensminger

  • Hero Member
  • *****
  • Posts: 1846
Re: Target weighting
« Reply #36 on: March 30, 2005, 06:59:21 AM »
wow,........is all that information really necessary..?
Logged
Pages: 1 2 [3]
« previous next »