win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: low top weight layout  (Read 1411 times)

rymacatthedisco

  • Hero Member
  • *****
  • Posts: 1631
low top weight layout
« on: May 13, 2008, 08:40:22 AM »
im recieving a cell that was an x out cuz of the top weight being around 1.7 or 1.8, what is a good layout i could use so that the ball doesnt burn up in my backswing. ive got decent speed 17+ and decent revs, and i track medium to low looking to use this for nationals. thanks guys
--------------------
RYAN MCDANIEL...Northern Illinois University bowling

www.newballz.com/forum
great new website!!!

FOS!!!

Diamonds...she''ll pretty much HAVE to!!!
Logged

 

mrbowlingnut

  • Hero Member
  • *****
  • Posts: 5727
Re: low top weight layout
« Reply #1 on: May 13, 2008, 04:48:05 PM »
I think low top weight matters about as much as the CG stuff, I have this ball I would go pin over finger line and the backend will pickup. It is pretty much a mid-lane and backending  type of ball, pin under will smooth it out somewhat.

Edited on 5/13/2008 4:48 PM
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: low top weight layout
« Reply #2 on: May 13, 2008, 04:50:45 PM »
With your speed and polish this ball will not hook in backswing!


Top weight can be raised in drilling to make this a big backending league ball after you get back by drilling a weighthole past 6 3/4 inch from the grip center this will actually raise the ending top weight(lane 1 strategy) and increase the instablity in the ball to flare more(brunswick).

BUT for now....most at nationals like smoothness and control.  With that setup low top weight setup .....I guess you got it!!!!
  Smoothness the usual result!

REgards,

Luckylefty

--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

rymacatthedisco

  • Hero Member
  • *****
  • Posts: 1631
Re: low top weight layout
« Reply #3 on: May 13, 2008, 04:52:37 PM »
right now its pin under the fingers on the midline i believe and the cg is kicked a little and the mb is swung pretty far out so im thinking it should start pretty quickly
--------------------
RYAN MCDANIEL...Northern Illinois University bowling

www.newballz.com/forum
great new website!!!

FOS!!!

Diamonds...she'll pretty much HAVE to!!!
Logged

LuckyLefty

  • Hero Member
  • *****
  • Posts: 17348
Re: low top weight layout
« Reply #4 on: May 13, 2008, 05:06:12 PM »
should...nice if you have a heavy oil in the fronts and mids then with this low top weight a nice strong backend shot.

If that is what you have heard Nationals is sometimes you are set.

Where is weighthole...this can tweak reaction a good amount.

REgards,

Luckylefty




--------------------
Open the door...see what's possible...and just walk right on through...that's how easy success feels..
Logged
It takes Courage to have Faith, and Faith to have Courage.

James M. McCurley, New Orleans, Louisiana

rymacatthedisco

  • Hero Member
  • *****
  • Posts: 1631
Re: low top weight layout
« Reply #5 on: May 13, 2008, 05:23:33 PM »
not positive bout the weight hole, ill have thursday so ill post some pics friday
--------------------
RYAN MCDANIEL...Northern Illinois University bowling

www.newballz.com/forum
great new website!!!

FOS!!!

Diamonds...she'll pretty much HAVE to!!!
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24524
Re: low top weight layout
« Reply #6 on: May 13, 2008, 06:36:27 PM »
quote:
im recieving a cell that was an x out cuz of the top weight being around 1.7 or 1.8, what is a good layout i could use so that the ball doesnt burn up in my backswing. ive got decent speed 17+ and decent revs, and i track medium to low looking to use this for nationals. thanks guys
--------------------
RYAN MCDANIEL...Northern Illinois University bowling
!


I strongly suspect that a 1.7 - 1.8 top weight is not a usual reason to mark a ball as an X-out. Many people will barely remove 2 ounces drilling the 3 finger holes. That will leave 0 =/- .3 ounces top/bottom, almost insignificant with today's dynamic cores, no less mass bias/asymmetric core.s

So I believe there could be another reason for this ball being labelled an "X-out". Was the ball marked that way or the box? Did the seller tell you why it was marked that way?
--------------------
"None are so blind as those who will not see."
Unofficial Ballreviews.com FAQ
Logged
"None are so blind as those who will not see."

charlest

  • Hero Member
  • *****
  • Posts: 24524
Re: low top weight layout
« Reply #7 on: May 13, 2008, 06:39:43 PM »
quote:
right now its pin under the fingers on the midline i believe and the cg is kicked a little and the mb is swung pretty far out so im thinking it should start pretty quickly
--------------------
RYAN MCDANIEL...Northern Illinois University bowling
!!!


Your rev rate, the ball's surface, the oil amount/pattern, and the pin position are the chief determinants of the ball's starting up early or not, NOT the MB nor the top weight. MB position and top weight are way down the list.
--------------------
"None are so blind as those who will not see."
Unofficial Ballreviews.com FAQ
Logged
"None are so blind as those who will not see."
Pages: [1]
« previous next »