Author Topic: Mutant Question (Read 1767 times)

3M Dust Remover · « **on:** February 25, 2010, 10:40:31 AM »

my mutant is drilled pin above ring finger and doesn't seem to want to move on the backend for me. i just had it baked and brought back to 2000. it seems to skid on me where my cell pearl, in oob pin up moves nice on the backend, is my mutant burning up?

charlest · « **Reply #1 on:** February 25, 2010, 06:44:25 PM »

More than likely there isn't enough oil for the Mutant, which needs a degree more oil than the Cell Pearl.
--------------------
"None are so blind as those who will not see."

3M Dust Remover · « **Reply #2 on:** February 25, 2010, 11:06:18 PM »

should i throw some polish on it? maybe bring it up to 4000?

Xcessive_Evil · « **Reply #3 on:** February 26, 2010, 01:06:41 AM »

quote:
my mutant is drilled pin above ring finger and doesn't seem to want to move on the backend for me. i just had it baked and brought back to 2000. it seems to skid on me where my cell pearl, in oob pin up moves nice on the backend, is my mutant burning up?

Where is the MB marking for each of these two? If it's closer to your thumb than the Cell Pearl is then all that means is that the Mutant is going to go into roll later. But, that isn't to say it isn't burning up, but please provide more info.
--------------------
www.youtube.com/track8401

http://smg.photobucket.com/albums/v690/Phoenix_RsX/Arsenal/

J_w73 · « **Reply #4 on:** February 26, 2010, 01:16:16 AM »

mb placement is important but from what I have seen the mutant is very lane condition specific.. Most of the people I have seen in this area are throwing them on conditions that don't have enough oil.. and they all don't like the ball..

--------------------
18 mph,350 rpm,PAP 5 1/2 x 3/8up, 15 deg axis tilt, varied rotational axis deg.. usually 45+
HighGame 300 x 4, High Series 808
Book Average 205,PBA Xperience 185

icewall · « **Reply #5 on:** February 26, 2010, 09:19:30 AM »

you need oil for that ball to perform well.

also make sure you're not just hitting the ball with 2000 or 4000 grit as the ball comes when you buy it at 500 grit then 2000 grit. if the balls surface gets too smooth by removing the 500 grit from the factory the ball will go long and skid on the backend. (this goes for balls that came 500,1000,2000, etc as well!)
--------------------
tweener
300 revs
16 mph
17 degrees of tilt

when you're feeling blue,
just say to yourself "what would BallBaggins do?"

Locke · « **Reply #6 on:** February 26, 2010, 01:18:16 PM »

The Mutant Cell is the strongest ball Roto has made. This ball needs a whole lot of oil if you have any sort of revs. We have a couple guys who throw them in my league. They only have about 225-250rpm they can throw it. If I tried it on that pattern it was be a terrible. As a rule of thumb that ball should probably not come out unless the oil is 38+ ft.
--------------------
They call me the thread killer...

Always be sincere, even when you don't mean it

The Cell Pimp

Motogp69 · « **Reply #7 on:** February 26, 2010, 07:19:12 PM »

My wife had the same problem, and admittedly I thought I bought her a dud, but then we went to our normal league house that has plenty of oil and the ball is such a beast I had to take it to 4000 and throw on a light polish.

The ball needs oil or it will die at your feet.
--------------------
Videos at:
http://youtube.com/user/Gsnap21

"The framers of our Constitution believed that if the people were to be sovereign and belong to different religions at the same time then our official religion would have to be no religion at all. It was a bold experiment then as it is now. It wasn''t meant to make us comfortable, it was meant to make us free."

Edited on 2/26/2010 8:19 PM

Author Topic: Mutant Question (Read 1767 times)

3M Dust Remover

Mutant Question

charlest

Re: Mutant Question

3M Dust Remover

Re: Mutant Question

Xcessive_Evil

Re: Mutant Question

J_w73

Re: Mutant Question

icewall

Re: Mutant Question

Locke

Re: Mutant Question

Motogp69

Re: Mutant Question