Author Topic: How can a RSX be drilled for a stroker? (Read 1696 times)

dev · « **on:** July 13, 2005, 01:21:18 PM »

I'm a stroker(more speed than revs) looking for skid-snap reaction on RSX, but not sure how am I gonna drilled it for heavier condition, not flooded ;P

Er, playing outside line, 1st arrow straight down the lane.

Edited on 7/13/2005 9:16 PM

dev · « **Reply #1 on:** July 13, 2005, 10:49:28 PM »

if the pin is under the ring, it would cre8 a more earlier roll rite? better midlane reading too?

dev · « **Reply #2 on:** July 13, 2005, 11:01:11 PM »

i'm stroker, dont really have the revs to snap the ball. anw, i had same a silver streak pearl which really snaps hard on med light conditions, but the pin is drill 11.30 of my ring finger.(im a lefty)

tloy · « **Reply #3 on:** July 14, 2005, 07:16:49 AM »

If you are looking for something comperable to the SS pearl I would go with the RS1 over the RSX. The Rsx is earlier than the RS1. I have both and both are great balls. If you al ready have the RSX I would leave in box condition and drill strong with the pin over the ring finger and cg kicked out about 1 to 1 1/2 inches. This should give you plenty of snap!!!! Good Luck!!!!
--------------------
Todd Loy

Jeffrevs · « **Reply #4 on:** July 14, 2005, 08:03:27 AM »

agree with Todd
--------------------
JEFF
"Chance to squint at a sky so blue that it hurts your eyes just to look at it."

dev · « **Reply #5 on:** July 14, 2005, 08:41:20 AM »

I'm not finding something to compare with my SS pearl, guess i made ya guys think wrongly. I want something stronger that i can add on top of SS pearl.

Mustang Guy · « **Reply #6 on:** July 14, 2005, 09:43:08 AM »

I suggest a 3x3 drill. Due to your lack in revs and higher ball speed a stronger pin position will allow the ball to hook when the lanes are slicker for you. This should fit nicely above your SS Pearl. Don't be afraid to lightly scuff it if needed.

Thanks,
--------------------
Roger Noordhoek
Office Manager
Roto Grip, Inc.
888-450-6920
RogerN@rotogrip.com
www.rotogrip.com

For all your Roto Grip Logo Merchandise please visit www.rotogear.com

dev · « **Reply #7 on:** July 14, 2005, 09:50:32 AM »

3x3 drilling? I'm not quite good regarding this terms of drilling.

maybe you can tell me where should I put my pin and my CG?

tloy · « **Reply #8 on:** July 14, 2005, 12:05:33 PM »

Dev,

This is a stacked drilling with pin and cg 3" from your pap(positive axis point). Max flare with early and strong midlane according to RotoGrips drill sheet. Good luck. Roto Grip Rules!!!!!!
--------------------
Todd Loy

novawagonmaster · « **Reply #9 on:** July 15, 2005, 09:08:34 PM »

My RSX is drilled 3&3/8 stacked. I'm a stroker, and I am VERY happy with this drill/reaction. Works very well on normal house shot (for me!).
--------------------
Jon (in Ohio)

CHROME WON'T GET YOU HOME!

Author Topic: How can a RSX be drilled for a stroker? (Read 1696 times)

dev

How can a RSX be drilled for a stroker?

dev

Re: How can a RSX be drilled for a stroker?

dev

Re: How can a RSX be drilled for a stroker?

tloy

Re: How can a RSX be drilled for a stroker?

Jeffrevs

Re: How can a RSX be drilled for a stroker?

dev

Re: How can a RSX be drilled for a stroker?

Mustang Guy

Re: How can a RSX be drilled for a stroker?

dev

Re: How can a RSX be drilled for a stroker?

tloy

Re: How can a RSX be drilled for a stroker?

novawagonmaster

Re: How can a RSX be drilled for a stroker?