win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Epicenter OOB finish?  (Read 11879 times)

novawagonmaster

  • Hero Member
  • *****
  • Posts: 4279
Epicenter OOB finish?
« on: November 11, 2009, 02:58:20 AM »
My Epicenter has finally started tracking up enough where it is moving a little earlier than I would like. The OOB finish was a hit for me, so I don't want to take a chance and end up with something too different. How should I go about getting this ball back to the OOB finish? I have a good assortment of abralon and polish to use.
--------------------
Jon (in Ohio)
http://lxforums.com/board/showthread.php?t=177027

Logged

 

RyanRPS

  • Hero Member
  • *****
  • Posts: 862
Re: Epicenter OOB finish?
« Reply #1 on: November 12, 2009, 06:01:09 AM »
Nova, take it to 4000 Abralone and polish, and you should find it reacting like new..

Ryan

Edited on 11/12/2009 7:01 AM
Logged

novawagonmaster

  • Hero Member
  • *****
  • Posts: 4279
Re: Epicenter OOB finish?
« Reply #2 on: November 12, 2009, 08:45:14 AM »
Will do. Thanks Ryan.
--------------------
Jon (in Ohio)
http://lxforums.com/board/showthread.php?t=177027

Logged

novawagonmaster

  • Hero Member
  • *****
  • Posts: 4279
Re: Epicenter OOB finish?
« Reply #3 on: November 20, 2009, 03:12:25 PM »
I went 360, then 500, then 4000, followed by a light dose of 3m Finesse II. The ball seems just a "smidge" longer than OOB, but that's OK. End result is on par with what I was looking for.

Thanks again.
--------------------
Jon (in Ohio)
http://lxforums.com/board/showthread.php?t=177027

Logged

charlest

  • Hero Member
  • *****
  • Posts: 24526
Re: Epicenter OOB finish?
« Reply #4 on: November 20, 2009, 08:10:42 PM »
Ryan,

I'd like to know if his following the Storm/Roto-Grip 500 grit/4000 grit scenario is what you had in mind or should he have done the full sequence of 500/1000/2000/4000 grit, then polish. The two are VERY different.

Thank you.
--------------------
"None are so blind as those who will not see."
Logged
"None are so blind as those who will not see."

novawagonmaster

  • Hero Member
  • *****
  • Posts: 4279
Re: Epicenter OOB finish?
« Reply #5 on: November 22, 2009, 08:58:35 PM »
Actually, I was wondering the same thing as I was standing there with the 4k pad in hand

Just curious. What would the difference be in reaction had I used the 1k and 2k pads before the 4k?

End result, I am happy with the reaction. Shot 786 with it tonight (which is a personal best by a few sticks).
--------------------
Jon (in Ohio)
http://lxforums.com/board/showthread.php?t=177027

Logged

DaveW

  • Full Member
  • ***
  • Posts: 159
Re: Epicenter OOB finish?
« Reply #6 on: November 23, 2009, 02:07:16 AM »
Congrats on the PB!

That Finesse It is good stuff, I use that on a lot of my equipment. It gives a good tacky shine compared to liquid polishes and usually gets polished balls pretty close to factory finish. Because it cuts i also find i never really need to sand/pad to anything over 1000. I actually get a ball directly from 600 to finished using it once, but it took quite a lot of pressure, polish and my spinner is pretty fast.

Always better to use more intermediate steps when finishing to get more consistant results.
--------------------
Dave W - Seismic Staff
www.seismicbowling.com
Logged

Dean Richards

  • Sr. Member
  • ****
  • Posts: 315
Re: Epicenter OOB finish?
« Reply #7 on: November 24, 2009, 07:37:18 PM »
I actually didn't like the box finish on the ball. I polished 1, took one down to 1000, and another down to 2000. They all roll real well
--------------------
Lindenwood University
Seismic Amateur Staff
Logged
Multiple casher in handicap 9 pin events
Pages: [1]
« previous next »