win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Factory Prep on T-Road Pearl  (Read 1326 times)

backupball

  • Hero Member
  • *****
  • Posts: 539
Factory Prep on T-Road Pearl
« on: December 30, 2007, 02:01:58 PM »
I looked on the Storm website for this but couldn't find it, all it says is "1500 Polished". Does anyone know how they prepare the surface before they apply the polish? I want to get the surface as close as original to what it was out of the box. TIA
--------------------
thanks,
backupball
Logged

 

n00dlejester

  • Hero Member
  • *****
  • Posts: 3354
  • The Dude Abides
Re: Factory Prep on T-Road Pearl
« Reply #1 on: December 31, 2007, 01:51:44 AM »
I would say e-mail Storm and ask them how they prepped the ball before polishing it. They responded to a lot of my random questions (particle load percentages of stuff) and did it FAST. But if I had to answer your question, I would say they probably wet sanded it to something low at first, say 500, then wet sanded it again to 1500, and then threw the polish on.
Logged
"This is not 'Nam. This is bowling. There are rules."

Slopsurprise

  • Hero Member
  • *****
  • Posts: 2100
Re: Factory Prep on T-Road Pearl
« Reply #2 on: December 31, 2007, 07:41:18 AM »
I have never had any luck getting a storm ball back to their "1500 Polished" even by following their instructions via Email.

It has been my experience, if it says 1500 polished, leave it alone and dont change the surface unless you hate the factory surface that much. IT will never act even close to the same again.
Logged

JMORRIS

  • Hero Member
  • *****
  • Posts: 625
Re: Factory Prep on T-Road Pearl
« Reply #3 on: December 31, 2007, 08:05:04 AM »
I use Reacta Shine.  That is what Storm recommends to clean and polish to 1500 grit.
Logged

greenefam

  • Hero Member
  • *****
  • Posts: 852
Re: Factory Prep on T-Road Pearl
« Reply #4 on: December 31, 2007, 10:43:54 AM »
I resurface to 1500 all the time.

use 500 abralon (wet) using either the 4 side or 6 side method
use 1000 abralon (wet) using either the 4 side or 6 side method
use Reacta Shine using either the 4 side or 6 side method

It will be darn close to box 1500 after that
Logged

Goof1073

  • Hero Member
  • *****
  • Posts: 2433
Re: Factory Prep on T-Road Pearl
« Reply #5 on: January 22, 2008, 06:04:40 AM »
I was wondering if you utilized their Pro Finish Step Two compound if that would get it back to original?
Logged

loose5682

  • Hero Member
  • *****
  • Posts: 1466
Re: Factory Prep on T-Road Pearl
« Reply #6 on: January 22, 2008, 06:25:34 AM »
I just hit mine out of the box before the press with a 2000 pad and then used Powerhouse Factory Finish on top, a little shinier than 1500 polished, but still not TOO much of a difference, and much easier to repeat in our shop as we don't carry Storm polishes.
--------------------
Andrew Loose

"Technology is anything that's really cool that you don't know how it works, and if it breaks, you have to buy a new one!"
Logged
Just because you can, doesn't mean you should
Pages: [1]
« previous next »