win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: My drilling on a Virtual Energy  (Read 1660 times)

joblo1978

  • Jr. Member
  • **
  • Posts: 81
My drilling on a Virtual Energy
« on: November 29, 2009, 11:48:48 PM »
After spending a good while getting to know the dual angle and more about ball layouts I've decided on the following for me VE.

Dual angle: 45 deg x 5.75" x 40 deg

5.75" x 3.5" x 3" Pin Buffer

PAP is 5 3/4" by 1/2" inch

I'm going for lots length and backend snap with this one

I have matched speed and revs at about 350 with a high track.

What do you guys think?
Logged

 

the pooh

  • Hero Member
  • *****
  • Posts: 615
Re: My drilling on a Virtual Energy
« Reply #1 on: November 30, 2009, 08:52:47 AM »
From my experience and Mo's charts, that would be a hook and set layout. To get a sharp breakpoint, you need the mass bias at about 5" and the pin at your 5 3/4". This would put your drilling angle at 70*. 45* is between a forward roll and hook and set drilling. You could also decrease your pin buffer a little. I would go 30* or around 1 1/2' to 2". This would give you the quick transition you are looking for. I definitely would go with 70* drilling angle if you don't want it to roll early. Being a bit of a high tracker, you could keep the 40* val angle to be flare safe, but you definitely need a longer pap to mass bias distance or you will end up with a lot of midlane read instead of backend.
--------------------
the pooh
Logged
the pooh

joblo1978

  • Jr. Member
  • **
  • Posts: 81
Re: My drilling on a Virtual Energy
« Reply #2 on: November 30, 2009, 11:12:05 AM »
I don't understand where I'm going wrong with my understanding of layouts?
Logged

the pooh

  • Hero Member
  • *****
  • Posts: 615
Re: My drilling on a Virtual Energy
« Reply #3 on: November 30, 2009, 12:01:12 PM »
Go to https://www.buddiesproshop.com/36/Asymetrical_Layout_Guide.htm This chart is gold! I use it to layout all my asymmetrical balls and it works beatifully! Use it to get the reaction you are looking for. Hope this helps!
--------------------
the pooh

Edited on 11/30/2009 1:02 PM

Edited on 11/30/2009 1:04 PM
Logged
the pooh

joblo1978

  • Jr. Member
  • **
  • Posts: 81
Re: My drilling on a Virtual Energy
« Reply #4 on: November 30, 2009, 12:29:23 PM »
So a big thing that I take from this is that because I'm a high track player, I cannot really deviate from MB positions 1 or 2 on any layout.

I recently obtained a prosect and discovered where my PAP was.  I'm tired of generic drillings from dudes in the pro shop.  I want to start pushing my layouts and get what I'm looking for out of my gear.

Thanks for this link. It is helpful and I'll add it to the other documents I've been collecting.

I've been working on an all inclusive excel document to get all this stuff down.
Logged

joblo1978

  • Jr. Member
  • **
  • Posts: 81
Re: My drilling on a Virtual Energy
« Reply #5 on: November 30, 2009, 08:10:04 PM »
So this is what I have come up with.

70 deg x 5.75" x 30 deg
5.75" x 5.5" x 2 1/4" Pin Buffer

This puts the pin about 1.5" right above my bridge and MB right right about the 1 o'clock edge of thumbhole.  Probably gonna go through the key a bit.

I'm looking for this thing to have good length on dryer lanes, second shift and late night bowling.

Ball needs to go long, turn hard and look like someone just kicked it into the pocket.
Logged

the pooh

  • Hero Member
  • *****
  • Posts: 615
Re: My drilling on a Virtual Energy
« Reply #6 on: November 30, 2009, 11:57:12 PM »
Sounds like a better layout. Just remember though,the backend is more a function of the bowler''s release than the layout! If you don''t have high rotation of axis and decent rpm''s, you''re never going to get that "kicked left" look. The surface you put on it will have a big influence also.
--------------------
the pooh

Edited on 12/1/2009 0:59 AM
Logged
the pooh

tommygn

  • Hero Member
  • *****
  • Posts: 694
Re: My drilling on a Virtual Energy
« Reply #7 on: December 01, 2009, 07:03:47 AM »
If you want a ball for second shift conditions, and still want the ball to kick, You may want to look into a Reign. This is what the Reign was designed for. The Virtual Energy has a very strong core, and wants to roll early, but the polished box finish allows it moderate length. The Reign has a pearl cover, and a higher RG, less diff weight block, and is designed to open up the backend of the lane. The Virtual Energy will give you the best reaction on fresher medium, medium-oily conditions that has oil up front, and clean to moderate carrydown lane conditions.
--------------------
Tommy Gollick
Storm Regional/Pro Shop staff
Red Crown Pro Shop Harrisburg, PA
stormbowling.com
Logged
God creates us with a blank canvas, and the "picture" we paint is up to us. Paint a picture you like and love!

joblo1978

  • Jr. Member
  • **
  • Posts: 81
Re: My drilling on a Virtual Energy
« Reply #8 on: December 01, 2009, 08:02:18 PM »
Well, maybe I shouldn't have used the term "dry".  These are subjective terms after all.
Logged

joblo1978

  • Jr. Member
  • **
  • Posts: 81
Re: My drilling on a Virtual Energy
« Reply #9 on: December 02, 2009, 10:45:22 AM »
I think I've settled on a 65* x 5 x 30*

Should compliment what I also have in the bag.

Anyone got any more tips?
Logged
Pages: [1]
« previous next »