win a ball from Bowling.com
« previous next »
Pages: 1 [2]

Author Topic: Box Surface of Hy-Road  (Read 11465 times)

Geetaan

  • Hero Member
  • *****
  • Posts: 683
Box Surface of Hy-Road
« on: July 01, 2010, 12:11:07 PM »
Hey all, I have a quick question... I am going to resurface my Hy-road, I know the box is 1500 polished... I dont have 1500 at the moment, and was thinking of doing either 1000 polished or 2000 polished. what would you guys recommend? I am up to any other surface suggestions. I am going to use this probably as my benchmark ball if that helps.

Logged

 

T C 300

  • Hero Member
  • *****
  • Posts: 550
Re: Box Surface of Hy-Road
« Reply #16 on: July 02, 2010, 11:46:13 PM »
quote:
I would use 500/1000/light coat of reacta shine from Storm.
1500 with my surface factory pro as per Storm Tech dept
500/2 min
1000/3 min
polish cycle 2 min
This is the Storm factory process for the 1500 surface!
--------------------
Use "IT" and BOWL UP A STORM!!


W O W!!!  5 min of sanding???!!!  sounds more like tryn to rub off the labels...  lolol
Logged

EFFEN 10

  • Sr. Member
  • ****
  • Posts: 341
Re: Box Surface of Hy-Road
« Reply #17 on: July 03, 2010, 06:17:49 PM »
quote:
quote:
I would use 500/1000/light coat of reacta shine from Storm.
1500 with my surface factory pro as per Storm Tech dept
500/2 min
1000/3 min
polish cycle 2 min
This is the Storm factory process for the 1500 surface!
--------------------
Use "IT" and BOWL UP A STORM!!


Is the process different for different balls?  Storm tech gave me different instructions for my rapid fire solid and it has the same 1500 grit polish finish as other storm balls.

Edited on 7/2/2010 11:24 PM



I've used Storms suggested technique on all my bowling balls,including non-Storm equiptment.Works well for me.Remember its JUST a bowling ball.
--------------------
The more I practice,the luckier I get.
Logged
The more I practice,the luckier I get.

r534me

  • Hero Member
  • *****
  • Posts: 936
Re: Box Surface of Hy-Road
« Reply #18 on: July 03, 2010, 07:06:45 PM »
I've used the process on non storm equpment as well.  I worked on my friends black widow bite and vibe and he loves the reaction.

Here is the instructions from Mike from Storm

That ball was 1500 grit polished,
 
Here is the process for 1500 grit factory finish,
 
500 grit Abralon pad – sand for 15 seconds on 4 sides of the ball
Grey scotch Brite pad – sand for 40 seconds on 4 sides of the ball
Storm Step Two finishing compound – polish lightly for 15 seconds on 2 sides of the ball
 
It is best to use this process on a ball spinner and when first doing this, use new pads.

That seems to differ from everyone elses posts.
Logged

icewall

  • Hero Member
  • *****
  • Posts: 906
Re: Box Surface of Hy-Road
« Reply #19 on: July 03, 2010, 07:29:40 PM »
If you have storm step 2  I have found using:

500 for about 20 seconds a side

then use storm step 2 and "step" it up by using small amounts until the ball is shiney like it comes OOB. works every single time!


if you use a grey pad you can easily shine the ball up too much and raise the underlying grit. its just my opinion and what I have found to work. but for right now my experience says 500 straight to step 2 is the way to go.


if you have NO step 2 then 2000 plus polish is kinda close. but who knows truly if it should be 2000 or 3000. probably 3000 but I''m not 100% sure on that, seems like more surface to me.

Edited on 7/3/2010 7:31 PM
Logged

tburky

  • Hero Member
  • *****
  • Posts: 1071
Re: Box Surface of Hy-Road
« Reply #20 on: July 03, 2010, 11:12:11 PM »
Quote
If you have storm step 2  I have found using:

500 for about 20 seconds a side

then use storm step 2 and "step" it up by using small amounts until the ball is shiney like it comes OOB. works every single time!




best way to do it.
Logged
Pages: 1 [2]
« previous next »