win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Anyone suggest a layout?  (Read 1684 times)

Hellbound

  • Full Member
  • ***
  • Posts: 223
Anyone suggest a layout?
« on: December 28, 2005, 01:29:46 PM »
Desert Heat..15 lb 2" pin, 2 3/4 top.
Speed app 14 mph..ave revs...release results in end over end roll.

Want to drill this for length and smooth backend.My problem is I track high and usually put the pin above ring to keep me "safe".Previous pin "under"
drills usually clip thumb.
Would like to try pin under again if anyone can suggest a layout that will work.
Thanks in advance......
Logged
Ambition is a poor excuse for not having enough sense to be lazy.......

 

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Anyone suggest a layout?
« Reply #1 on: December 28, 2005, 09:45:57 PM »
Hellbound,

There is a zone or area on a ball that ball drillers know is the safe zone for a pin to be placed. If you track that high if you go under you are more than likely going to clip. There really wouldn't be a layout with pin under that you could use that wouldn't clip unless you alter your release.

For a smooth reaction you may be able to get away with a pin on your PAP layout....but that still would have a chance to thump.

-Carl
--------------------
C-G Pro Shop (owner/operator)
Youngstown Ohio

Track Intl.-Amateur/Pro Shop Staff

www.trackbowling.com

www.startabowlingrevolution.com


Tag Team Member #1

Edited on 12/28/2005 10:37 PM
Logged
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

Hellbound

  • Full Member
  • ***
  • Posts: 223
Re: Anyone suggest a layout?
« Reply #2 on: December 28, 2005, 09:56:23 PM »
EX....With a 2" pin is it feasible to put the pin over fingers?

SIX...Thanks...dont know my PAP
Logged
Ambition is a poor excuse for not having enough sense to be lazy.......

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Anyone suggest a layout?
« Reply #3 on: December 28, 2005, 10:23:12 PM »
Hellbound,

Well-----honestly....it wouldn't be easy you would end up drilling the fingers VERY deep.

Ironhorse's suggestion of pin in finger isn't too bad, but it could also still make you clip. Some people are afraid of trying layouts with the pin in the ring finger, but it works great. Basically your pin safe zone is going to be from the middle of your finger holes up, if you are below that then it is going to be close.
A buddy of mine that works at another pro shop in the area has drilled balls with 2 inch pins for high trackers. He has put them on the upper portion of the bridge. It has worked well when he has done it. I have not tried this method yet.

Goodluck,
-Carl
--------------------
C-G Pro Shop (owner/operator)
Youngstown Ohio

Track Intl.-Amateur/Pro Shop Staff

www.trackbowling.com

www.startabowlingrevolution.com


Tag Team Member #1
Logged
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

Slopsurprise

  • Hero Member
  • *****
  • Posts: 2100
Re: Anyone suggest a layout?
« Reply #4 on: December 29, 2005, 08:14:49 AM »
My experience with the Desert heat is that if you dont have a medium track or lower, its going to thump! I have used 2 different drillings with the same result (pin under bridge CG stacked, Pin under ring CG in center of span). I can throw a plastic ball without it thumping holes but not a Desert Heat for some reason. BTW, mine had a 2 inch pin also.
--------------------
Nothing hits like a Hammer!!

Yea.....nothing hits that bad!!!

Edited on 12/29/2005 9:04 AM
Logged

SteveAustin2808

  • Hero Member
  • *****
  • Posts: 1417
Re: Anyone suggest a layout?
« Reply #5 on: December 29, 2005, 08:33:11 AM »
Hey Guys,

I have read alot of posts where people are thumping holes with the Desert Heat. I have one and I do NOT thump over the finger or thumb holes. Mine is drilled with a 4 1/2" Pin, Pin @ 1 o'clock and a weight hole on my PAP. I'm just wondering why I seem to be the only one who doesn't roll over any of the holes drilled in the Desert Heat. God Bless you all!

--Michael--
--------------------
What Are You Waiting For? Get on the FASTTrack to success!!

Track -- Building success stories, one bowler at a time!

McCorvey's Pro Shop Supporter
http://http://www.mccorveysproshop.com/
Logged
Michael Price - Office Manager
McCorvey's Bowling World Staff - Phone: (256) 539-1560
Hammer Amateur Staff
michaelp@mccorveysproshop.com

Hellbound

  • Full Member
  • ***
  • Posts: 223
Re: Anyone suggest a layout?
« Reply #6 on: January 04, 2006, 02:51:08 AM »
Well..Finally got my DH puched up.Went with Carls idea of pin next to ring finger with cg kicked out.Almost identical to diagram 4 on Track drill sheet.
Couldnt be happier....ball gets great length.smooth arc to the hole...murders the pins....
No sign of the dreaded "thumb-thump", tracking about 1/4" from hole.
Perfect result.
Thanks to everybody for your input,was much appreciated.
Logged
Ambition is a poor excuse for not having enough sense to be lazy.......
Pages: [1]
« previous next »