win a ball from Bowling.com

Author Topic: Break in period with Inertia?  (Read 1610 times)

DP3

  • Hero Member
  • *****
  • Posts: 6093
Break in period with Inertia?
« on: November 07, 2006, 11:14:02 AM »
Hey guys.  I don't read much of this forum anymore but I did do a search before I made this post.  Seems like no one is mentioning anything about the Inertia.  A Track Staffer who is a good friend of mine gave me this ball with pretty good specs.  I was hesistant on drilling it, but decided, what the hell and went with my favorite assymetrical layout.  That is with the pin 1.5" above the midline and 4 3/4" from my PAP with the MB in the 70 degree position.  

I've tried the Inertia for a total of about 4 games(just an estimate, more like about 40-50 shots) on 3 different patterns.  What I found with the Inertia is that on my THS which is a lighter volume, but has quite a bit of carrydown due to a sparatic oiling machine(you rarely get a full strip of the lanes), the Inertia spins up off of the hand and dies out on the backend.  Very ugly reaction to say the least.  At first I thought the ball was burning up, but there is 8 1/2" of flare that I am getting from this ball with about half of it in the oil, but hardly any continuation in the backend.  I did take it to a house notorios for a flood of oil in the middle of the lane and the pattern drops off severely outside of 6.  In this house I experienced the same thing.  The ball flared up a ton in the oil(and came back juiced with oil rings), but did nothing off the spot.  The times I did hit pocket either left a nasty flat 10 or 8, and times I got the ball into a decent angle, I left some very solid 9s that made me shake my head.

Maybe this is just too much ball for my hand, maybe not.  With so few shots on it, I was wondering if anyone is noticing any type of "break-in" period with this ball where after so many games it magically comes to life and starts rolling very well?  I know on alot of the activator shells for me, it took about 10-12 games for them to start rolling how they were intended to.  Maybe this ball is the same way?  Any advice legion?


If not, $65 shipped takes it

 

FastTracker33

  • Hero Member
  • *****
  • Posts: 3472
Re: Break in period with Inertia?
« Reply #1 on: November 07, 2006, 07:23:58 PM »
Hmm, there is definetly a break in period i think with this ball. I have a very weird layout on mine, and if you wanna see it i have a pic. But anyways, my Inertia did that SAME exact thing, it would actually flare almost to the other side of the ball!! LOL. and it wouldn't even move. I took the polish off of it, and it's now at about 800-1000 grit, i used the abralon machine sander too. My Inertia now moves perfectly, nice even archy ball, but that's how it's drilled. My Inertia isn't drilled VERY strong, but it hooks when nothing else does, lol.

I would say to give it some time. Throw plenty more games with it, and see what happens. I would also recommend to take the polish off if you're not liking the reaction. Go to about 1000 to start with. Hope you like it
--------------------
-BrIan
Formerly known as Hammer33
PoWer MaChine, Action MaX, DEsert HeAt
"Join the Revolution.. or be Destroyed by it!"

Join the Track Legion now at  http://trackbowling.com/  
"Track...you Just can't Beat That!"

shipper50

  • Hero Member
  • *****
  • Posts: 1228
Re: Break in period with Inertia?
« Reply #2 on: November 07, 2006, 07:41:55 PM »
I shot 740 with mine out of box. Was on synthetics with medium heavy oil 10-10 at 40 feet. It was a arcing ball that with me playing around 12 to 8 I didn't miss the hole. It is  not a backend type of ball, more arc and play to hit the pocket and not try to over hook the ball.

Shipper

scotts33

  • Hero Member
  • *****
  • Posts: 8452
Re: Break in period with Inertia?
« Reply #3 on: November 07, 2006, 09:53:44 PM »
My layout pin above/right of ring 4.5" pin to pap MB .75" from thumb.  75 deg. layout.  Best reaction w/ 1000 to 2000 abralon  knock the shine off at least for my length and THS bowled on.  Rolled many decent league games with it 279 highest so far.  Interesting thing no 9 pins left for me.  

On a THS, I start with a Saturn on fresh backends normally and move in with the Inertia.  Or start with a Radar if I need more mid lane roll and older wood.  Most of the time I bowl on synthetic.  

Play with the surface DP3.
--------------------
Scott

Scott

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Break in period with Inertia?
« Reply #4 on: November 07, 2006, 10:49:59 PM »
DP3,

What are the ending static weights?

OOB I like the Inertia......once I went over the polish lightly with a grey pad just to break the surface a bit I REALLY liked it!

-Carl
--------------------
Carl Hurd
C-G Pro Shop (owner/operator)
Youngstown Ohio

Track Intl.-Amateur/Pro Shop Staff
www.trackbowling.com


Tag Team Member #1

TAG TEAM COACHING!!!!!!
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

DP3

  • Hero Member
  • *****
  • Posts: 6093
Re: Break in period with Inertia?
« Reply #5 on: November 07, 2006, 11:07:17 PM »
1/8th oz thumb, 3/4oz side.  It had a 1.5" pin and 2.2oz top

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Break in period with Inertia?
« Reply #6 on: November 07, 2006, 11:11:26 PM »
Personally I would try taking the positive side down to about 1/4 positive. I think that would help.
--------------------
Carl Hurd
C-G Pro Shop (owner/operator)
Youngstown Ohio

Track Intl.-Amateur/Pro Shop Staff
www.trackbowling.com


Tag Team Member #1

TAG TEAM COACHING!!!!!!
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

Tweener92

  • Hero Member
  • *****
  • Posts: 991
Re: Break in period with Inertia?
« Reply #7 on: November 08, 2006, 11:42:44 AM »
There really wasn't a break in period for mine. Mine was drilled then immediately wetsanded to 1000. Took it to the lanes the next night and shot 670
--------------------
----------------
Tim
Member of The Track Legion


R.I.P. Mom
Aug 29 1957 - Aug 3 2006

mrbowlingnut

  • Hero Member
  • *****
  • Posts: 5727
Re: Break in period with Inertia?
« Reply #8 on: November 08, 2006, 12:15:35 PM »
Knock off the polish with grey pad or 1000 pad, ball did about nothing first few shots oob then took the grey pad to it by hand. I then shot 226,244 the last two times i have thrown it, since i am ball junkie i have been throwing other stuff since. Ball like to played from the 1 st arrow with medium heavy oil with fresh backends, mine is 4 1/2 pin to pap and mb is 4 inches to pap. Pin is under ring finger so not length drilling at all.

DP3

  • Hero Member
  • *****
  • Posts: 6093
Re: Break in period with Inertia?
« Reply #9 on: November 08, 2006, 02:28:07 PM »
I guess the general consensous is adding surface?  The problem is, very few places in this area have "fresh backends", especially the 2 primary houses that I am bowling out of.  Yes the ball will make a move on the backend, but between the wide array of equipment people are using, about 3-4 frames into the first game the pattern blows up in the track area and the oil is carried down(I am guessing they are using really low grade quality oil that pushes around like mercury).  So when you get left and try to bounce it out, the ball checks up midlane and stops in the oil in the backend.  Then when you try to get deeper and ride the oil line, the carrydown keeps everything from continuing.  

I am not sure how much surface will be too much surface since it's already flaring as soon as it touches the lane.  I am thinking I'm just not in a heavy enough volume with clean enough backends to see this ball shine.  This might just be for tournaments/sport shots sake only since that'll be the only time I see a condition consistant enough from the start to the finish with clean backends.  I am bowling a tournament this weekend on a challenging pattern(will most likely be USBC open shot) so I'll leave it be until then and if there's still a bad reaction I'll give it one more chance next league session with a cover adjustment and see what happens.  Thanks.

scotts33

  • Hero Member
  • *****
  • Posts: 8452
Re: Break in period with Inertia?
« Reply #10 on: November 08, 2006, 03:20:26 PM »
DP3--What ball do you now use on this condition?  Your Rush?  

I'm using mine on a similar condition and it's working for me pretty well.  I amy leave a 10 now and again.  I do change my release as I move into the lane more drag type and around the ball for more axis rotation.
--------------------
Scott

Scott

DP3

  • Hero Member
  • *****
  • Posts: 6093
Re: Break in period with Inertia?
« Reply #11 on: November 08, 2006, 03:58:21 PM »
The typical league night I go through about 3-5 balls because the "look" on the lanes changes that much every 4-5 frames.  The shot is always inconsistant, and there's no telling from week to week how and when they will break down.  Last monday I was completely lost, but managed to hold the pocket/head pin for most of the night.  

I started 5th arrow out to 15 with a Saturn which looked good in practice, but by frame 4 of the 1st game it wasn't making the turn back, but when I moved right it was even less drive to carry.  I then went back inside with the Inertia and flushed 2 back to back 9 pins, a 3-6-10 through the beak, a washout, then another stone 9 pin to finish game 1 with a 164 while only missing the pocket twice.  I ended up playing the "cliffhanger" shot with my teammate, going 6 out to as far on the ditch as possible without throwing it in the ditch.  I rotated a Super Sonic and Horizon Pearl but everytime I came out of the ball too clean it'd jump through the face(imagine that....a shot when you're not rewarded for getting out of the ball well, lol).

No one really had a good look the entire night, I think high set was maybe 700 something and somehow the slower speed player was using The One, playing about 10-5 and he held pocket the entire night.  It seemed as if every pair was much different.  His had a ton of hold inside the track area, so when the ball got to the bounce it never overhooked in the oil in the middle.

I'm thinking I just may be a victim of terrible conditions due to this faulty machine they keep using to oil the lanes.  It plays like your typical wet/dry THS up front, and from 50ft on it seems like there's oil from there through the pindeck because the machine never gets a full stripping of the backends.  Ah well....only about 24 more weeks left to go through this

cmoore3wins

  • Hero Member
  • *****
  • Posts: 708
Re: Break in period with Inertia?
« Reply #12 on: November 08, 2006, 10:07:08 PM »
Hey DP3,

Static weights have little or no affect on balls reaction. Try surface first....
--------------------
MoRich makes me mo rich, cuz I sell the 300 & 800 rings on eBay!

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Break in period with Inertia?
« Reply #13 on: November 08, 2006, 10:09:18 PM »
cmoore3,

I notice that you have morich in your signature......tell Mo what you just typed below and see if he agrees. From the ball show today that I attended, I think he would disagree.



--------------------
Carl Hurd
C-G Pro Shop (owner/operator)
Youngstown Ohio

Track Intl.-Amateur/Pro Shop Staff
www.trackbowling.com


Tag Team Member #1

TAG TEAM COACHING!!!!!!
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

cmoore3wins

  • Hero Member
  • *****
  • Posts: 708
Re: Break in period with Inertia?
« Reply #14 on: November 09, 2006, 12:48:21 AM »
Was at the MO seminar in York on Monday - Sat at the same table as him and Jimmy while Mo was mapping balls!!!!!!
--------------------
MoRich makes me mo rich, cuz I sell the 300 & 800 rings on eBay....
While you're leaving corners, I am laughing inwardly....
My core has a hole in it, but your score sheet does....
I flip out ten pins, you flip them off....


Edited on 11/9/2006 1:41 AM