win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Drilling up an Unleashed  (Read 1042 times)

srlunatic

  • Hero Member
  • *****
  • Posts: 4316
Drilling up an Unleashed
« on: December 24, 2003, 06:01:25 AM »
Greetings!

I have a Phenom Unleashed that I will have drilled up this weekend.  Was hoping to get some input on what pattern to drill this with....

Here is what I am looking for.....

length and a strong but controlled move to the pocket...

PAP is 5 3/4
Pin in 3 inches
TW is 3 oz....

looks as if CG is about 1/4 - 1/2 right of line drawn direct from Pin to MB...

Was thinking 45 Degree drilling with a nice bit of polish.....would think this would give me what I am looking for????.....Any other specs on me and my bowling are in my profile...

Thanks for the help!!!!

Mike
--------------------
My personal savior is common sense.
How can being so RIGHT be so very WRONG?
Logged
They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety.

 

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Drilling up an Unleashed
« Reply #1 on: December 24, 2003, 10:04:49 PM »
Mike,

Try the Pin under and between the fingers, and the MB inbetween the thumb and your VAL. I would go directly in the center, if your PAP is 5 3/4, I would go probably 3 inches right of the thumb hole.



Goodluck,

Carl
Logged
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

tenpinspro

  • Hero Member
  • *****
  • Posts: 4161
Re: Drilling up an Unleashed
« Reply #2 on: December 25, 2003, 06:27:30 AM »
Hi Mike,

Ex is on the ball as usual.  I have mine pin under, split fingers, but I placed my mb(about 2) a little closer to my val for an even smoother reaction and this is exactly what I get.   I can't handle balls w/ too much backend, causes o/u on shots out here.  Hits like a truck, last 2 weeks in league, shot 723 and 721, more amazing for ME was going 60 clean.  Good luck......
--------------------
Rick Leong
Ten Pins Pro Shop
Track Pro Shop Staff
Logged
Rick Leong - Ten Pins Pro Shop
Co-Founder - Tag Team Coaching
"El" Presidente of the Legion

srlunatic

  • Hero Member
  • *****
  • Posts: 4316
Re: Drilling up an Unleashed
« Reply #3 on: December 26, 2003, 11:50:25 AM »
Thanks for the input!!

Question for you....I have a very high track and have tried pin under type drillings but have always flared over fingers/thumb and really haven't tried a pin under in quite sometime.  Will this drilling create/cause the same problems??


--------------------
My personal savior is common sense.
How can being so RIGHT be so very WRONG?
Logged
They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety.

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Drilling up an Unleashed
« Reply #4 on: December 26, 2003, 12:39:28 PM »
I also track high. Balls with the strong MB (as told to me by Del Warren and Mo Pinel) can move your track 2 inches. So you should be safe. I do not hit the holes on any of my stuff drilled with the pin low. Example though----I had a Storm Super Power(has MB, but was not strong, and probably not marked correctly), I had the pin in the same location as with the Unleashed and I hit the thumb hole every time.


I would really say that you are safe with this drilling.


goodluck
Logged
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/
Pages: [1]
« previous next »