win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Hmmm, thinking of tinkering with the Machine  (Read 1116 times)

AdrianS

  • Hero Member
  • *****
  • Posts: 1122
Hmmm, thinking of tinkering with the Machine
« on: May 27, 2008, 06:29:48 PM »
Prob a little more than a tinker actually!! The pin/cg/MB alignment on this ball is what is now called 'pro cg' The cg is about 1 1/2' out of line left of a line from the pin to the mb.

Now what im thinking of doing is getting the pin under the middle finger and swinging the mb over so its past my PAP ( which is 5' over) and punch the X hole right through it!! Good idea or will it roll bad? I dont use it much so im willing to to take a chance with it
--------------------
Time for some REAL bowling!!!
Logged
Time for some REAL bowling!!!

 

C-G ProShop-Carl

  • Hero Member
  • *****
  • Posts: 5825
Re: Hmmm, thinking of tinkering with the Machine
« Reply #1 on: May 30, 2008, 09:45:19 AM »
Adrian,

This layout is a good length and stable type set up. The only problem is that you have to be careful because it can cause some to roll over the middle finger or even reverse flare for some as well. I can try to let you know if it would be safe if you can get me your PAP and approx axis rotation.

Thanks,
Carl
--------------------
Carl Hurd
C-G Pro Shop (owner/operator)
with locations in:
Youngstown Ohio (West Side Lanes)
and
Boardman Ohio (Camelot Lanes)

Track Bowling Tech Advisor
The Legion Lives @ www.trackbowling.com


Tag Team Member #1

TAG TEAM COACHING!!!!!!/Co-Founder
Logged
Carl Hurd

Austintown Ohio (Wedgewood Lanes)

900 Global, AMF Staff Bowler

Tag Team Member #1

<b><i>TAG TEAM COACHING!!!!!!</i></b>/

Slopsurprise

  • Hero Member
  • *****
  • Posts: 2100
Re: Hmmm, thinking of tinkering with the Machine
« Reply #2 on: May 30, 2008, 02:37:38 PM »
Couldnt this possibly hook and set with a standard run of the mill PAP.
Logged

AdrianS

  • Hero Member
  • *****
  • Posts: 1122
Re: Hmmm, thinking of tinkering with the Machine
« Reply #3 on: May 30, 2008, 06:49:35 PM »
Not sure about my rotation, i know it aint 0 or 90 anyway!!, The only time i had trouble with an Assymetrical of mine going over a finger a little was my Phenom when i(very briefly) had it drilled pin next to ring finger and MB in the track area.

Might even just go pin under ring and hole 5- 5 1/2" over instead of 6 3/4. That would be like my Phenom is laid out low, except with the MB a bit further around
--------------------
Time for some REAL bowling!!!
Logged
Time for some REAL bowling!!!

AdrianS

  • Hero Member
  • *****
  • Posts: 1122
Re: Hmmm, thinking of tinkering with the Machine
« Reply #4 on: June 09, 2008, 08:01:25 PM »
Threw it last night how it is, with the surface(my faithful green pad!!) i have on it now im getting an alright hook/set look so ill prob leave it alone. When my Robo gets here its layout should give me a little earlier hook than the Machine with similar shaped move off the break so i think i'll have the look i want already with that(and saved myself $70 for a plug and redrill!!)
--------------------
Time for some REAL bowling!!!
Logged
Time for some REAL bowling!!!
Pages: [1]
« previous next »