win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Test Staff  (Read 1312 times)

Blindstag

  • Jr. Member
  • **
  • Posts: 85
Test Staff
« on: September 10, 2005, 07:48:35 AM »
Hi all,

Have just joined the visionary test staff progam through my aussie distributor and have received my AMB Solid & B/G Centaur, hope to get them drilled this week. I'm looking forward to contributing to the 'Visionary Community' as a whole.

thanks
--------------------
Dale Stewart
Visionary Test Staff
-----------------------------------------------------------------------
Imagination is more important than knowledge - Knowledge is limited,  
Imagination encircles the world ~ Albert Einstein
Logged
Dale Stewart
-----------------------------------------------------------------------
Better to be called a geek than an idiot

 

I_Bowl4Money

  • Hero Member
  • *****
  • Posts: 677
Re: Test Staff
« Reply #1 on: September 10, 2005, 06:07:33 PM »
Any ideas as to how you want to get them drilled??
--------------------
Steve
Visionary Shirt Staff

VBP 100% - - If you have the money then I've got the time!!
http://www.bowl4money.com
http://www.visionarybowling.com
http://www.maysbowlingandbilliards.com
Logged
Stephen Hahn
PBA Professional
Brunswick Regional Staffer
VISE Regional Staffer

GargoyleFlunkie

  • Full Member
  • ***
  • Posts: 150
Re: Test Staff
« Reply #2 on: September 10, 2005, 09:57:08 PM »
its good to see new members in the test staff i havnt gotten a chance to throw any of the centaurs but have all the gargoyles and the g3 gryphon and a charcoal executioner but i just ordered a b/g centaur hopefully its hits like the rest of visionarys stuff
--------------------
proud member of the visionary test staff home of the some of the greatest unknown balls in the world
Logged

livespive

  • Hero Member
  • *****
  • Posts: 4819
Re: Test Staff
« Reply #3 on: September 10, 2005, 10:23:01 PM »
Welcome to the staff.
--------------------
Eric T. Spivey, P.E.
 Visionary Test Staff Member
http://www.visionarybowling.com
http://www.maysbowlingandbilliards.com
Logged

Blindstag

  • Jr. Member
  • **
  • Posts: 85
Re: Test Staff
« Reply #4 on: September 11, 2005, 04:03:04 AM »
how to get them drilled - the B/G centaur will be drilled as close as possible to a setup given to me by Scott:

Layout 5 1/2 x 4 1/2
Pin above fingers centered above bridge
CG kicked right 1 1/2"s from grip center on horiz. center line
X hole 5/8" diam. 3" deep on VAL 1" below horiz. center line
Polished as high as I can get it. This should let me play the dry track area.

The AMB Solid - I'm not sure, I want the ball to be used for heavy oil and to arc. So I'm thinking (going from the sheet here) - Pin C position with mass bias in position 1, or (depending on what my new driller recommends) Pin position D with mass bias in position 1 or 2.

Any other thoughts would be most welcome.
--------------------
Dale Stewart
Visionary Test Staff
-----------------------------------------------------------------------
Imagination is more important than knowledge - Knowledge is limited,  
Imagination encircles the world ~ Albert Einstein
Logged
Dale Stewart
-----------------------------------------------------------------------
Better to be called a geek than an idiot

I_Bowl4Money

  • Hero Member
  • *****
  • Posts: 677
Re: Test Staff
« Reply #5 on: September 11, 2005, 09:31:03 AM »

Blindstag,

They sound like good choices...the funny thing is, is with the layouts you have chosen, I would reverse them....I would take the layout you were going to place on the B/G and put that one on the SOLID and the layout you were going to put on the SOLID put on the B/G.

My suggestions would be the following:

B/G - 4 1/2 x 5 1/2 (4 1/2 pin to PAP) (5 1/2 CG to PAP)
Let the pin fall wherever, adjust if desired to not drill through pin unless you are comfortable doing so.

SOLID - 4 x 3 (4 pin to PAP) (3 CG to PAP)
Let the pin fall wherever, adjust if desired to not drill through pin unless you are comfortable doing so.

Modify the covers on each to get desired reaction...because of the pin being in a little stronger position on the B/G, polishing it will probably be necessary to play on the drier condition but should maintain a little more energy and less likely to roll out on you.

Just my thoughts.


--------------------
Steve
Visionary Shirt Staff

VBP 100% - Newest Staff Member of Spares ProShop
http://www.bowl4money.com
http://www.visionarybowling.com
http://www.maysbowlingandbilliards.com
Logged
Stephen Hahn
PBA Professional
Brunswick Regional Staffer
VISE Regional Staffer

Blindstag

  • Jr. Member
  • **
  • Posts: 85
Re: Test Staff
« Reply #6 on: September 11, 2005, 02:22:39 PM »
Thanks steve,

I am going to a new driller, my old one retired. So he wants to watch me bowl etc, to see what he thinks should be done. I will make the suggestion to him and see what he says.

regards


--------------------
Dale Stewart
Visionary Test Staff
-----------------------------------------------------------------------
Imagination is more important than knowledge - Knowledge is limited,  
Imagination encircles the world ~ Albert Einstein
Logged
Dale Stewart
-----------------------------------------------------------------------
Better to be called a geek than an idiot

GargoyleFlunkie

  • Full Member
  • ***
  • Posts: 150
Re: Test Staff
« Reply #7 on: September 12, 2005, 12:12:02 AM »
well i have my g3 drilled the exact same as my violet garg and it goes about 5 feet longer but jumps alot harder no matter how the oil is except heavy cause neither balls move to good in that but for the average house/medium oil shots that some houses might use for tournaments i ussually use it when my violet garg is hooking to early and just move left a couple boards and swing it
--------------------
proud member of the visionary test staff home of the some of the greatest unknown balls in the world
Logged
Pages: [1]
« previous next »